I have an older Black & Decker Sawcat #987. It does not appear to have any way of locking the spindle that I can find. I don’t think there is enough friction to run the motor to snug it up that way. I am aware of methods to loosen the bolt without a lock but these don’t seem to apply when tightening.
No matter what type of saw blade you use, you can get the saw blade dirty. 2 Press the saw lock button and rotate the saw blade until the lock mechanism engages. 4 Pull the upper saw blade guard and remove the old saw blade.
Not only table saws, but drills and circular saws are also equipped with a spindle. Once the blade is not moving, you can use the wrench that you get when buying the circular saw. You can use this article as a guide to better understand what the spindle lock is and how to use it to change the blade on your circular saw.
Instructions: Secure your work piece and mark your cut. Align the line of cut with the 45° blade guide notch on the base when making 45° bevel cuts. Install the battery or plug the saw in and make your cut on the waste side of your cut mark.
how to lock circular saw Related Question:
How do you lock the blade on a Craftsman circular saw?
Locate the blade lock button or lever usually found on the backside of the upper guard. While depressing the button, place the wrench over the bolt and turn the blade with the wrench until you feel the blade lock in place.
What is a spindle lock?
Most cordless impact drivers have a feature called spindle lock that, when selected, locks the motor’s spindle so the chuck cannot turn. Most models of impact driver will have ‘automatic spindle lock’, which means that the chuck and metal bit are automatically locked when the speed control trigger is released.
How do you use a circular saw without a sawhorse?
In some cases, it might be better to use your circular saw without a sawhorse. If you need to make cuts without a work support, you can lay a sturdy, stationary surface under the material while making cuts.
Why is my circular saw binding?
A circular saw binds because of failure to ensure proper blade depth; setting the blade too deep presents a danger because more blade surface is exposed while cutting than a properly set blade. When the saw is too deep, kickback and binding will be inevitable.
How do you lock a Dewalt miter saw?
To lock the saw, press the handle down until the blade is as low as it can go. Then, press the lock pin back into the rail to secure the blade in place. Ensure that the saw is locked by pulling up on the handle with the pin pushed in. If the handle doesn’t move, your saw is locked.
Where is the arbor lock on a circular saw?
Place the saw on a wooden surface and pull back the blade guard. If the saw has an arbor lock button on the top of the housing, press it in. The arbor is the shaft the blade installs on. If there’s no lock button, press the blade into the wooden surface.
Why is my circular saw blade loose?
Bearings and washers are mainly responsible for holding a saw’s shaft in place. However, wobbles and misalignments may loosen the blade. This can cause problems while cutting. Moreover, the bolt of the circular saw may wear out after regular use.
What is Dewalt spindle lock?
The spindle lock button is provided to prevent the spindle from rotating when installing or removing wheels. Operate the spindle lock only when the tool is turned off, unplugged from the power supply, and has come to a complete stop.
What is drill spindle?
The spindle holds the drill or cutting tools and revolves in a fixed position in a sleeve. In most drilling machines, the spindle is vertical and the work is supported on a horizontal table. The sleeve or quill assembly does not revolve but may. slide in its bearing in a direction parallel to its axis.
Why is my circular saw burning the wood?
Pushing the stock through the saw too slowly is a common cause of saw blade burn. Sometimes a blade that feels dull might only be dirty. If wood pitch resins build up behind the teeth of the blade, the cutting speed will slow down, increasing the chances for burns. Commercial blade cleaners are sold for this purpose.
Why does my hand saw keep binding?
The wood you are sawing is closing the kerf and pinching the blade, Your cut isn’t straight, The set of the saw teeth is not large enough, so the kerf created by the blade isn’t wide enough to allow the saw room to pass without undue friction, or.
Can you clamp to a saw-horse?
Sawhorse clamps and saw guide These sawhorse clamps hold round or small items while cutting. A 2×3 “pressure block” locks your work in place while the square end of the channel guides your saw and gives you a square cut.
How much weight can a wooden sawhorse hold?
Folding Sawhorse with Adjustable Legs. Heavier duty than other models on the list, DeWalt’s sawhorses support a load capacity of up to 2,500 pounds per pair.
