Im wondering if renting a pickup truck and then tilting the saw on its spine, sliding it into the bed and tying it down would be an OK option. 02-12-2005, 5:41 PM #5 Scott, as others have said, transporting it on it’s spine is the Best way, and Best for the Saw, as this is it’s strongest side and would eliminate any “Twisting” of the saw’s frame. The loading instructions of rolling it to the truck and then tipping it into the truck on it’s Spine with the top toward the cab of the truck is also correct.
IMO you could move the saw either lying on its spine or standing up. If you are moving yourself then you may find lying it down on its spine the easier approach because you can slide it up to the truck/trailer standing up, and then tip it in and onto its spine. Posts: 4,763.Threads: 1.Joined: Jan 2004 Location: Eugene, OR. I think the salient question is how are YOU planning to move the MM16. Is it going by common carrier, loading it in a pickup or a trailer etc.
Whether you’re a beginner or could just use a refresher, we’re going to walk you through the process for a perfect bandsaw blade adjustment setup every time, no matter what blade you install. Lower the upper blade guide, open the wheel housing(s) and blade guard and carefully remove the blade. So it should be no real shocker that you’ll encounter conflicting schools of thought regarding blade placement on the wheels and how it affects blade “Drift”.
I must admit, when I know someone is watching that hasn’t seen me fold up a bandsaw blade before, I do it extra fast and super snappy to make it seem even more dazzling. I learned how to coil a bandsaw blade like this pre-YouTube and over the phone from the kids at Wood-Mizer, who supply and sharpen my blades. From there, whip the portion of the blade furthest from you towards the ground and just as the blade nears the ground give it a quick jerk up, with a snap.
Even a low-end bandsaw blade tension meter can cost $300. If you use your bandsaw a lot or are doing delicate work, having the proper tension on the blade can be critical and the only way to accomplish this is with a bandsaw blade tension meter. With the bandsaw blade properly installed, and tensioned, and the blade guides properly set, the next issue is to make sure that the bandsaw table is square and level. We suggest that you go through the setup steps in this how to set up a bandsaw properly: the ultimate g guide before starting a new project and each time you change your bandsaw blade.
how to load bandsaw Related Question:
How do you transport a band saw?
There are really only 2 ways to transport a bandsaw safely, either upright and well bolted and strapped down, or, more simply, on its back (spine) with some home-made chocks or framing to secure it so that it can not twist or fall over on its side.
How do I move heavy equipment by myself?
Ramps: Forget about using your strength to lug heavy furniture over stairs and into truck beds or moving trucks. Ramps make it much easier and safer to place a large or unwieldy item on a raised area. Moving straps: If you’re wondering how to move something heavy, turn to moving straps, also called lifting straps.
Can you put a bandsaw blade on upside down?
Typical bandsaw blades can be flipped “inside out” to make the teeth point the other direction. On some knife edge style blades and grit edge blades you can get a fresh sharp cutting edge from a blade this way, just by flipping it inside out.
Which way should the teeth face on a bandsaw?
Installing A Bandsaw Blade Make sure the teeth point downward.
How far should the safety guard be above the stock?
Keep guards in place at all times. The blade guard should be from 1/8 to ¼ inch above stock. Keep hands away from blade and do not open upper or lower bandsaw doors while blade is in motion.
What is the throat on a band saw?
The throat is the distance from the blade to the vertical frame section of the body of the saw. This distance determines the width of cut that can be completed on the band saw. The throat on a free-standing cabinet band saw typically exceeds the 12 to 14-inch throat of smaller, bench-top models.
What must the operator do before operating the bandsaw?
Before the start of any sawing operation, the bandsaw machine operator needs to check the electrical connections — saw to power source. Look for cable splits or crimps and assure that a fork lift or other shop equipment are not inadvertently left near or plugged into a needed outlet.
How do you pack a table saw for moving?
Any sharp-edged garden tools – saws, knives, gardening shears, hoes, rakes, etc. – need to be made safe for transportation. Use old blankets, old towels, or a few sheets of bubble wrap to cover their blades or sharp edges, then fix the protective cover with the help of zip ties or string.
Which is the best method of moving a heavy object?
When lifting anything heavy, it’s good to use your legs to lift, not your back. Make sure to bend at your knees as you lift and not at the waist. Carry the items close to your body to rely more on your arms to do the work and to maintain your balance. Avoid twisting your body during the lift and while moving items.
How can heavy machinery be transported easily without lifting?
Rolling friction is less than sliding friction. We can apply the above property to move a heavy machinery from one place to another, in the absence of a crane. We can create rolling friction by placing round logs of wood below the machine.