I dribble some bar oil onto the nose of the bar, while turning the sprocket with my fingers every time I dress the rails on the bar. I’ve never had a sprocket fail and I have cut a chitload of wood over the years. Like others have said in this thread, that bearing in the sprocket gets oil from the bar while cutting too.
Check and replace bar and chain oil regularly to reduce friction, keep the saw from wearing out faster, and to make cutting easier. Be sure to use bar and chain oil, Not regular motor oil. Gas chainsaws use about one tank of bar and chain oil for every tank of fuel, so fill the reservoir every time you fill the tank.
Use only Universal powered by McCulloch bar and chain oil. This oil has been specially developed to retain its viscosity at the extreme temperatures generated by the chain and bar. If the bar is fitted with a nose roller, this should also be lubricated regularly.
how to lube chainsaw bar Related Question:
Can you use wd40 on a chainsaw bar?
To clean the bar, you should add some degreaser or lubricant such as WD-40® Multi-Use Product, mixed with warm water. Once soaked with the solution, use a rag to remove all the dust and grease. If there is stubborn grime, you can use a wire brush to remove it.
Can any oil be used for chainsaw bar oil?
Generally, chainsaws can handle a wide range of lubricants. Vegetable and canola oils work well, and automobile motor oil will too, as long as you observe the SAE ratings and use the appropriate oil weight for the season. Always use fresh, never used, oils.
Can I use 10w30 for chainsaw bar oil?
As a matter of fact, you can actually use regular 10w30 motor oil on a chainsaw as one of the alternatives in case you don’t have bar and chain oil. That’s because 10w30 oil has enough thickness and viscosity that will allow it to withstand the friction that is happening whenever you are using a chainsaw.
Do STIHL chainsaw bars need grease?
A lubricating tool for select STIHL. The Guide Bar Grease Gun is designed for lubricating the sprocket nose bearings on guide bars that have the grease hole. Current STIHL guide bars offer maintenance free sprocket noses, some competitor’s guide bars still require additional grease.
Do Oregon bars need grease?
Most Oregon and Husqvarna bars (photo above) traditionally come with a greasing hole. Most STIHL bars do not. However, STIHL bars are built with thin shims on either side of the bearing/sprocket assembly to help keep debris out.
How do you add oil to a bar?
The steps are quick and easy: Set your chainsaw on a level surface, bar side down so that it lays flat. Allow a minute for the oil to settle, then unscrew the cap to the saw’s bar and chain oil reservoir. Using a small funnel, slowly pour the bar and chain oil into the reservoir, taking care not to overfill.
What weight is chainsaw bar oil?
What viscosity is chainsaw bar oil? The viscosity of chainsaw bar oil can vary depending on the formula but 30W is standard. In cold weather, a thin 10W chainsaw oil may be advantageous, while very hot temperatures may require a much thicker 40W or 50W formula.
What do you use for a chain saw oil?
Use canola oil – Canola oil is currently the most common environmentally compatible chain-and-bar lubricant. Canola-based chain and bar oil has been extensively tested in Europe.
Can WD-40 be used as chainsaw oil?
No. You should never use WD40 as chain lubricant since WD-40 is NOT a true lubricant. WD40 is primarily a solvent or rust dissolver.
How often should you oil a chainsaw?
The chain saw should be oiled before each cut. For Manual Oiling System: Lubricate the saw chain by pressing the bulb on the oil reservoir cap twice before making each cut. Hold the bulb down for 3-4 seconds on each press. Automatic oiling system will keep the bar and chain constantly lubricated.
Can you use transmission fluid for chainsaw bar oil?
On occasion I’ve used tranny fluid to clean out old oil residue in old chainsaws . It works well . In addition to that tranny fluid seems to pump better on some saws with whimpy oilers in cold weather .
Can you use old motor oil for chainsaw bar?
Some people caution against using motor oil on a chain saw, but not for safety reasons or concerns about equipment. Bar and chain oil is stickier than regular motor oil, so it stays on the chain longer.
Can you use 10w40 in a chainsaw?
You can but it’s not very good for the chain or the environment. The Husqvarna / Stihl stuff is much thicker and vegetable based so it doesn’t fling off the chain as easily or poison your garden! 10w30. Thicker.
Can I use 5w30 for bar oil?
You’ll be fine.
Does Stihl make guns?
So Stihl are making pump action shotguns now …