This is different than the oil that you mix with your gas to provide lubrication to the engine, and I’m going to describe below the importance of this task and explain how to oil your chainsaw for both the safety and care of your saw. Most saws come with a sample bottle of oil and suggestions of which oil to by- but for the most part, the oil is that same from one brand to the next. Saws are designed to feed oil as it runs, so most tanks are large enough to hold enough oil for a full tank of gas.
Check and replace bar and chain oil regularly to reduce friction, keep the saw from wearing out faster, and to make cutting easier. Be sure to use bar and chain oil, Not regular motor oil. Gas chainsaws use about one tank of bar and chain oil for every tank of fuel, so fill the reservoir every time you fill the tank.
At Gardening Products Review, we highly recommend oil manufactured for this specific use. Chainsaw shown in this video tutorial is the Redback 40V 12″ Li-Ion Cordless Chainsaw. The bar & chain oil featured in this video is Husqvarna Bar & Chain Oil – 1 Gallon.
how to lube chainsaw chain Related Question:
Can I use wd40 on my chainsaw?
We recommend using WD-40® Specialist® Fast Acting Degreaser and soak it for 10 to 15 minutes. Next, use a wire brush to remove all the grime (repeat several times) and wipe with a paper towel to make sure all the dirt is gone.
What oil do you use to lubricate a chainsaw chain?
Rapeseed-based (usually called canola) oil is currently the most common environmentally compatible chain-and-bar lubricant. Vegetable-based oils are triglycerides or natural esters that come from agricultural crops.
Do you need to lube a chainsaw?
You want lubrication of the actual chain against the bar. You don’t want to chain to burn – which is what might happen if there’s too much friction. Without oil, it causes frictional force on the motor in the chainsaw as well.
Can I use 10w30 for chainsaw bar oil?
As a matter of fact, you can actually use regular 10w30 motor oil on a chainsaw as one of the alternatives in case you don’t have bar and chain oil. That’s because 10w30 oil has enough thickness and viscosity that will allow it to withstand the friction that is happening whenever you are using a chainsaw.
How often should you oil a chainsaw?
The chain saw should be oiled before each cut. For Manual Oiling System: Lubricate the saw chain by pressing the bulb on the oil reservoir cap twice before making each cut. Hold the bulb down for 3-4 seconds on each press. Automatic oiling system will keep the bar and chain constantly lubricated.
Is chainsaw oil the same as motor oil?
Bar and chain oil is stickier than regular motor oil, so it stays on the chain longer. Motor oil flings off the chain more quickly, so if you try Terry’s tip, be prepared to refill the oil on your chain saw more quickly than with regular bar and chain oil.
Can I use regular motor oil as my chainsaw bar oil?
If your manufacturer’s bar and chain oil is unavailable, you can use SAE 30 weight motor oil to lube your chain during the summer and SAE 10 weight during the winter, according to the University of Missouri Extension.
Can I use vegetable oil instead of bar and chain oil?
Effective – Vegetable oils have natural properties including good lubricity, resistance to shear, a high flash point, and a high viscosity index. These qualities lend themselves to chain lubricant requirements similar to petroleum-based chain oils, and do not contribute to chain or bar wear over time.
What is special about chainsaw oil?
Chainsaw bar oil has a certain level of “slickness” to it. This slickness keeps the chain spinning at a fast rate without getting slowed down by the friction that occurs when metal rubs against metal. So, if you want to use the “correct” type of bar oil in your chainsaw, consult the manual and use what it suggests.
How do you adjust a chainsaw oiler?
To increase the oil flow, turn the automatic oiler adjustment screw counterclockwise. To decrease oil flow, turn the automatic oiler adjustment screw clockwise. While always wearing heavy work gloves, grasp the chain and pull it towards the nose of the chainsaw to ensure that the chain moves freely.
Can you use transmission fluid for chainsaw bar oil?
On occasion I’ve used tranny fluid to clean out old oil residue in old chainsaws . It works well . In addition to that tranny fluid seems to pump better on some saws with whimpy oilers in cold weather .
Can I use 2 stroke oil for chainsaw bar oil?
Can You Use 2 Cycle Oil As Bar Oil? You should only use two-cycle oil as the mix, never as a chainsaw bar oil alternative. Using two-cycle oil on the bar will not provide enough tackiness to stick to the chainsaw chain in the summer months. Two-cycle oil also will not work in the winter.
How often should you add bar oil to chainsaw?
Gas chainsaws use about one tank of bar and chain oil for every tank of fuel, so fill the reservoir every time you fill the tank.
How do you remove sap from a chainsaw chain?
My own favorite sap fighter is WD-40. Let it soak in for a couple of minutes, then take an old toothbrush to it.
Can you use brake cleaner to clean a chainsaw?
Can I Use Brake Cleaner To Clean My Chainsaw? If you are washing parts that are covered in oil, you should never use water on them. Instead, use carb or brake cleaner to blow out the dirt and oil more effectively.