My Stihl bar does not have the holes to grease it but i try to force some in buy filling the bar tip with grease. Sigidi , several on another website have said that the reason for not greasing the sprocket tip is because the grease attracts dirt. Most of my cutting is not plunging or bar buried so I would expect one low pressure area to be the grease hole which is effectively vented to atmosphere when the tip is exposed and the sprocket is rotating.
I dribble some bar oil onto the nose of the bar, while turning the sprocket with my fingers every time I dress the rails on the bar. I’ve never had a sprocket fail and I have cut a chitload of wood over the years. Like others have said in this thread, that bearing in the sprocket gets oil from the bar while cutting too.
how to lubricate chainsaw sprocket Related Question:
Do you grease a sprocket?
Re: Greasing Bar Sprocket It is more recommended to grease the tip at the end of the day to help push any debris/grit out of the bearings and coat the bearings with grease to keep them from rusting due to moisture and condensation that can form when the saw is not in use.
Can you use WD-40 to lubricate a chainsaw?
No. You should never use WD40 as chain lubricant since WD-40 is NOT a true lubricant. WD40 is primarily a solvent or rust dissolver.
Do you need to grease Stihl chainsaw bar?
The Guide Bar Grease Gun is designed for lubricating the sprocket nose bearings on guide bars that have the grease hole. Current STIHL guide bars offer maintenance free sprocket noses, some competitor’s guide bars still require additional grease.
What is bar oil for chainsaws?
What is chainsaw bar oil? Chainsaw bar oil is lubricant that is designed to reduce friction between the chain and bar. An oil reservoir releases the oil onto the bar. It’s picked up by the chain as it travels around the bar and then flung off in tiny droplets as the machine runs.
How often should you oil a chainsaw?
The chain saw should be oiled before each cut. For Manual Oiling System: Lubricate the saw chain by pressing the bulb on the oil reservoir cap twice before making each cut. Hold the bulb down for 3-4 seconds on each press. Automatic oiling system will keep the bar and chain constantly lubricated.
Do you need to oil a chainsaw blade?
To work properly, chainsaw chains and bars must be lubricated.In the past, most operators have used petroleum-based oils. When a chain saw is used, virtually all of the lubricant ends up in the environment.
Can I use 10w30 for chainsaw bar oil?
As a matter of fact, you can actually use regular 10w30 motor oil on a chainsaw as one of the alternatives in case you don’t have bar and chain oil. That’s because 10w30 oil has enough thickness and viscosity that will allow it to withstand the friction that is happening whenever you are using a chainsaw.
Is chainsaw oil the same as motor oil?
Bar and chain oil is stickier than regular motor oil, so it stays on the chain longer. Motor oil flings off the chain more quickly, so if you try Terry’s tip, be prepared to refill the oil on your chain saw more quickly than with regular bar and chain oil.
Do Oregon bars need grease?
Most Oregon and Husqvarna bars (photo above) traditionally come with a greasing hole. Most STIHL bars do not. However, STIHL bars are built with thin shims on either side of the bearing/sprocket assembly to help keep debris out.
Does STIHL make guns?
So Stihl are making pump action shotguns now …
Can I use gear oil as bar oil?
Unless you are using your chainsaw in hot conditions, gear oil is not a recommended alternative bar oil.
Can I use regular oil for chainsaw bar?
While motor oil is not the best substitute for chainsaw bar oil, it will work as a temporary measure if find you have no other option. The downside of motor oil is that it’s not sticky enough to stay on the bar and chain. So, when you’re using the chainsaw, the motor oil will fling off as you cut and make quite a mess.
Why do chainsaws leak bar oil?
When a chainsaw is in use most of the oil is absorbed by the log and sawdust produced by the chain, therefore leaving little to drip to the surface under the saw.
Can you refill an Oregon grease gun?
OVERVIEW. Oregon’s Grease Gun is pre-loaded with all purpose lubricant – it’s filled, easy to use and ready to go. The steel nose nozzle features a spring loaded pump action for sprocket nose guide bars. It’s easy to refill, and is effective in preventing premature wear and tear, especially on guide bar noses.
What is white lithium grease spray used for?
White lithium grease is used to keep components moving smoothly, free of friction and seizing. You can also apply it preventatively to protect against rust and corrosion. White lithium grease can be used to: Lubricate car door hinges.