Calipers can be clamped to the blade and used to measure the displacement of the points while the blade is tensioned. Set it so that the blade is taut when there is no tension on the blade. One end is on the stuff attached to the blade and the other end is attached to the band saw blade guide holder.
We’ve seen various methods for setting bandsaw blade tension, from fancy gauges to plucking the blade like a guitar string. Turn the tensioning handwheel until the tension gauge is at or a little above the recommended tension for your blade width. With the saw running, slowly release the tension-about 1⁄2 turn of the tensioning wheel at a time-until the blade starts to flutter, as shown at right.
On a machine with screw over spring tensioning, the most common on smaller machines, only really dependable way to set the blade tension is with a blade tension gauge. The machine manufacturer will provide a chart showing how much blade force is generated by any air pressure, and the blade tension in typical blade sizes. Over tightening the blade will shorten the life of the blade wheel rubber, bearings, and blade.
The jig works by measuring the amount of stretch in the bandsaw blade as force is applied by the bandsaw tension spring. Every 0.001″ of blade stretch is equal to 5,800 psi of tension over 5″ of blade. “When resawing, blade manufacturers recommend a blade tension of 15,000 psi. Therefore, you would need 0.0026” of blade stretch in order to reach the recommended amount of tension.
Running your bandsaw blade tension too loose can cause your blade to come off track another dangerous situation. Then you adjust the bandsaw blade tension to reflect what the manufacturer recommends the blade tension should be. The bandsaw blade flutter test, my opinion probably one of the best ways to properly set up blade tension.
Blade Tension Timber Wolf® Silicon steel blades are very stable at low tension or lower tension than what is normally recommended by most saw manufacturers and other blade manufacturers. If a specific cutting application requires that more tension be applied to the blade, such as when resawing large material or cutting green logs, the recommended force for these blades can be increased by as much as 20%. To apply the exact same blade tension each time saws would require a very expensive hydraulic or air strain tensioning system to create a repeatable tensioning method. Timber Wolf® blades from 1/8″ to 2-1/8″ for every cutting application; scroll cutting, curve cutting, ripping, cross-cutting,resawing, milling, metal cutting and Urethane Band Saw Tires.
how to measure bandsaw blade tension Related Question:
How tight should a tension bandsaw blade be?
The blade should deflect no more than 1/4 in. A good place to begin is to tension the blade until the meter reads proper tension for the next wider blade. For example, if you’re tensioning a 3/8-in.
How do you tension a Timberwolf bandsaw blade?
Shut the motor or engine off and wait until the blade comes to a full stop. Add another 10% of tension to the blade by turning the screw-tensioner approximately 1/8 to 1/4 turn. The “flutter test” is now complete and you are now at appropriate tension for that particular blade.
Why does my bandsaw blade wobble?
The blade on a saw left idle for long periods of time can leave an impression in the rubber tire which might cause erratic tracking. Purchase and install aftermarket replacement tires. (Search for “bandsaw tire” at woodcraft.com.) If you still see a back-and-forth motion, the culprit is probably the wheel itself.
Why did my bandsaw blade snap?
Machine Defects Even the best blades can fail if there is something else wrong with your bandsaw, and even a small misalignment of bearings or guides can put a twist in the blade as it goes around. Resulting in tension being applied in all the wrong ways which will lead to early breakage.
Why do bandsaws wander?
If the wheels are worn and do not have a distinct top to the crown then the blade will not know where to go, and may wander around. This of course can cause poor cut quality and difficulty in setting the guides.
What is Resawing on a bandsaw?
Bandsaw Resawing from the beginning: resawing is cutting a sawn plank of wood into thinner planks on a bandsaw. Thus the cut runs through the plank’s width, which distinguishes bandsaw resawing from ordinary bandsaw rip cuts where the blade runs through the stock’s thickness.
How do you measure a bandsaw?
To determine the size of a band saw, measure the distance from the blade to the throat. That measurement is a little more than the largest piece of wood the band saw can handle. The band saw’s large circular blade is placed around the tool’s top and bottom wheels. Some band saws have built-in fences.
What is the pitch of a sawmill blade?
The most commonly-used “all-purpose” tooth spacing is 7/8” (1.1 TPI pitch).
What is tension gauge?
Push & Pull Tension Gauge This is a multi-purpose dynamometer to measure compression and the competence tension of the measured object by using a head or hook.