“Using the wrong size bar or chain can damage the chainsaw and injure the chainsaw operator,” says Vince Christofora of Woodstock Hardware. Read on to learn how to measure your chainsaw’s bar and chain. Sometimes called a chainsaw blade, the chainsaw bar is the metal “Arm” that holds and supports the chain during cutting.
Measure the distance between any 3 consecutive rivets that hold the chain assembly together. The rivets are noticeable between the drive links and the cutters – the cutting teeth that lie on top of the chain. The pitch, together with the number of drive links, describes the chain’s length when seeking replacement chains.
The following explains how you measure a chainsaw chain and also includes some important tips for chain care. You may need to remove the chain to do this, but might be able to loosen the chain and then spin it above the bar to count. If you have ever wondered about what those numbers on a chainsaw bar meant, or was confused as to how you might match your existing chain to one in a store – worry no more.
how to clean your chainsaw Related Question:
Can I use wd40 to clean chainsaw?
Step 4: Clean the Chain We recommend using WD-40® Specialist® Fast Acting Degreaser and soak it for 10 to 15 minutes. Next, use a wire brush to remove all the grime (repeat several times) and wipe with a paper towel to make sure all the dirt is gone.
Do I need to clean my chainsaw?
No matter the power source, all chainsaws have an oil filter located under the cap of the bar lubricating tank. Fish the filter out and inspect it for dust. If clogged, it will restrict the flow of oil needed to keep the guide bar and chain lubricated. Clean with gasoline or replace as necessary.
How often should I clean my chainsaw?
For homeowners, this means you’ll need to clean your filter twice a year on average. Professionals may need to do it weekly, and sometimes even more frequently. The best time to clean or replace the air filter on a chainsaw for most people is at the start of the cutting season.
Can I clean chainsaw with brake cleaner?
Can I Use Brake Cleaner To Clean My Chainsaw? If you are washing parts that are covered in oil, you should never use water on them. Instead, use carb or brake cleaner to blow out the dirt and oil more effectively.
How do you clean a chainsaw after use?
After each use, wipe the chainsaw housing clean with a damp cloth. For battery models, you should also use the damp cloth to clean the battery and the battery slot. A paintbrush is useful for cleaning electrical contacts.
How often should you oil a chainsaw?
The chain saw should be oiled before each cut. For Manual Oiling System: Lubricate the saw chain by pressing the bulb on the oil reservoir cap twice before making each cut. Hold the bulb down for 3-4 seconds on each press. Automatic oiling system will keep the bar and chain constantly lubricated.
How do you clean a chainsaw without a compressor?
Make a solution using a gallon of water and a cup of household ammonia and soak these parts in the solution for 20 minutes. Once the soaking time is over, take them out and scrub using a stiff brush. Rinse them thoroughly using warm water.
What happens if you run a chainsaw without bar oil?
Without lubricant, the speed at which the chain moves over the chainsaw bar can cause some serious friction. A slowed-down chain and excessive fuel burning mean there’s a lot of friction between your bar and chain, which means a lot of heat is being produced that could do major damage to your saw.
Can I use 10w30 for chainsaw bar oil?
As a matter of fact, you can actually use regular 10w30 motor oil on a chainsaw as one of the alternatives in case you don’t have bar and chain oil. That’s because 10w30 oil has enough thickness and viscosity that will allow it to withstand the friction that is happening whenever you are using a chainsaw.
Is chainsaw oil the same as motor oil?
Bar and chain oil is stickier than regular motor oil, so it stays on the chain longer. Motor oil flings off the chain more quickly, so if you try Terry’s tip, be prepared to refill the oil on your chain saw more quickly than with regular bar and chain oil.
Do electric chainsaws need bar oil?
Electric chain saws derive their power from an electric source, so they don’t need fuel to run. Most gas chain saws require a premixed gas-and-oil fuel to operate properly. Electric chain saws don’t require this added oil, but the bar and chain do need to be properly lubricated.
Why does my chainsaw chain dull so quickly?
Dirt Causes A Chainsaw To Dull If you’re cutting through logs and your angle of approach is too steep, a simple cut through could nick dirt or even worse, rocks on the floor causing your chainsaw to jerk, thus dulling.
Do I need to oil my chainsaw?
You want lubrication of the actual chain against the bar. You don’t want to chain to burn – which is what might happen if there’s too much friction. Without oil, it causes frictional force on the motor in the chainsaw as well.
How much does it cost to service a chainsaw?
THE AVERAGE CHAINSAW SERVICE IS $100 TO $125 If we can find ways to help save you money, we will suggest them to you. If we do not feel it is worth repairing, we will tell you so.