Used extensively throughout the metalworking, woodworking, and lumber industries, these convenient saws are regular fixtures at countless industrial facilities. For your saw blade to retain its accuracy, it will need to receive consistent lubrication and band saw coolant. To ensure a consistently reliable performance out of your company’s band saws, you’ll need to stay on top of tool inspections and blade maintenance.
CHOOSING THE PROPER BAND SAW BLADE LUBRICATION NEVER USE WATER as a lubricant on band saw blades. “Pam” spray-on vegetable shortening is a great lubrication for 3/4″ WIDTH AND UNDER band saw blades on vertical saws. You wouldn’t ignore cleaning pitch off your table saw blade, jointer knives, planer knives or miter saw blade so it is obviously just as important on a bandsaw blade.
CHOOSING THE PROPER BAND SAW BLADE LUBRICATION. NEVER USE WATER as a lubricant on band saw blades. “Pam” spray-on vegetable shortening is a great lubrication for 3/4″ WIDTH AND UNDER band saw blades on vertical saws. In both cases, we know for a fact that lubrication of the body of the band increases band life by over 30%. Applied sparingly, you can cut grade lumber with NO staining to your product.
I don’t have as much experience as many, though I am in school to be a shop teacher, and I’d advise following the manual. A band saw cutting metal is much different than a drill bit, as a drill bit creates chips, and the lubrication is to prevent friction and heating if the drill bit. With a band saw, the blades move through the material, and have time to cool as it goes around, so for that reason I believe it is not needed.
A good-quality cutting fluid lubricating a bandsaw blade is an important factor in straight cutting. Choosing the right cutting fluid for this particular job will help to improve not only the cut but also prolong the life of the saw blade. Cutting fluid is important and a must when cutting through metal.
Dan said: Was watching on YouTube and a guy suggested using bar soap to lubricate metal cutting bandsaw blades – he even said it could used on milling cutters, drill bits, etc. If your saw is set up right, tension is right, you are selecting proper blades, you are cutting at the correct rate and using lube you should get decent life from any decent bi metal blade. If you want better blades, or you need a size that local stores aren’t going to stock, you could order Lenox or Starretts, or even more expensive blades from a place like MSCdirect.com, they can weld custom sizes for you as well as stocking common sizes.
The only issue is that I had to leave the cutting oil behind as I couldn’t take it with me. I have always seen some sort of thick brown oil used for this purpose does anyone know what the name of that oil is so I can order it. 04-24-2010, 06:39 AM #5 I don’t remember the exact name of Mobile’s STRAIGHT cutting oils, but they make some quality stuff if you really want to go the straight cutting way.
how to oil a band saw Related Question:
Do band saws need lubrication?
Lubrication is simply one of many maintenance procedures a band saw requires to properly carry out its job. In order for your saws to produce accurate cuts, you’ll also need to tend to the tool’s pumps and chip filters on top of the appropriate saw blade lubricant.
Do you need to oil a bandsaw blade?
Using an incorrect lubricant in your application has the potential to harm your blade, damage the material being cut and clog the machinery. Band saw blade lubricant is important, too, to getting smooth cuts. A reduction in friction means reduced vibration, smoother operation of the blade and a more consistent cut.
What oil do you use for a bandsaw?
BAND SAW KLEENKOOL is a premium quality oil specially formulated for the unique problems associated with high speed band saws. BAND SAW KLEENKOOL is engineered to lubricate, cool, and clean residue from band saw blades.
Can you lubricate a saw blade?
Luckily you don’t need much, just moisten your thumb and index finger on your tongue and run the blade up and down between them. If you need some lubricate for your saw blade but do not have any on hand, this is definitely your best bet. It doesn’t cost anything. Spit won’t cause premature blunting of your saw blades.
Why does my bandsaw stall?
Using a dull blade or the incorrect type of blade can cause the band saw to cut through work pieces slowly. The blade will also move slowly through the work piece if the blade is installed incorrectly. A weak drive motor can also cause the band saw to cut slowly.
Why is it important to use lubricant when using the blade?
The lubrication system acts as a blade wash, removing the hairs. For many products lubricating the blade also greatly assists the cutting action and eases the passage of the blade through the extrusion. This will reduce blade wear & lessen the cutting power needed to cut the product.
What kind of coolant do you use on a bandsaw?
We recommend a 20:1 dilution with tap water for most use cases. For aluminum, stainless steel, and other non-ferrous metals, we recommend QualiChem Xtreme Cut 251C. It resists the staining and hazing that sometimes happens with other coolants in aluminum. As with SnakeBite®, we recommend a 20:1 dilution for sawing.
How do you mix Lenox Band Ade?
Recommend mix rate 10:1 for mild steel, 5:1 for S.S. and other difficult to cut applications. Mixes to a transparent light orange/brown color. (Note: 10:1 refers to 10 parts water to 1 part coolant.)
What to use to lubricate piercing?
Lubricant. Any kind of safe lubricant will help the taper slide through the piercing more easily. Plenty of jewelry shops sell commercial-grade lubricant, but you can also use plant-based lubricants, like coconut oil or jojoba oil.
What is dry lubricant spray?
Product Overview. Dry lube spray provides superior lubrication and protection. Creates a dry film that resists dirt and reduces friction, wear. Ideal for locks, window, door tracks, drawers, catches and more.
What to coat table saw top with?
Using paste wax is the best way to lubricate the top of your table saw, which will help wood pieces slide across more smoothly when making cuts. Using paste wax is the best way to lubricate the top of your table saw, which will help wood pieces slide across more smoothly when making cuts.
What is paste wax?
Paste wax is a thick, creamy wax that is often applied with a cheesecloth or rag, buffing into the grains of the wood until a highly vibrant shine and gloss forms.
Why won’t my bandsaw cut metal?
Band saws are not suitable for cutting very thin sheet metal; a rule of thumb suggests the metal to be cut should be thicker than the depth of 3 band saw blade teeth, however they are excellent for cutting thin walled profiles such as box and angle.
Why does my bandsaw keep jamming?
If there are too few teeth in the cut (teeth are too large), this will also lead to teeth stripping and cracks from the gullets. Not enough teeth also cause jamming and sometimes distortion to the product you are cutting, especially thin walled pipe.
Why is my band saw not cutting?
Band Saw: Why won’t my band saw cut straight? When the band saw cuts crooked, a dull blade, improper feeding, loose blade tension or not using a work piece guide could be the cause. Use the rip fence or miter gauge to guide the work piece uniformly through the cutting blade to make straight cuts.