To make the proper cuts; you’ll need to install the correct blade, which means you’ll need to know not only how to change the band saw blade, but also how to adjust the saw to keep the blade that you do install tracking straight and true. In the following step-by-step tutorial, learn how to change your band saw blade as well as how to make the adjustments necessary to keep your band saw blade cutting properly. Before you can begin to truly tension and adjust the tracking on your new band saw blade, you’ll need to loosen the band saw guide blocks and rollers that keep the blade tracking properly.
Speaker: Today, I’m going to walk you through the process of changing a band saw blade. It’s pretty simple, but there are three main things to consider: blade tracking, blade tension, and guide adjustment. Since the blade is a continuous loop, the table is slotted so that you can get the blade out.
The rear blade guard wraps the bandsaw blade while protecting you in the event of blade rupture. All most all bandsaw problems are blade related and a dull blade can cause blade drift. Knowing how to change a bandsaw blade can easily help you get rid of these problems quickly.
Installing the blade is almost identical to taking it off, but this time you WILL need to re-adjust the upper and lower blade guides and the Thrust Bearing. So install the new blade by placing it on the upper wheel first, then the lower wheel, and now is a good time to take up a bit of slack in the blade. Before you start to align the blade on the wheel, make sure none of guides or thrust bearings are touching the blade … now, spin the upper wheel while adjusting the angle of the blade.
Whether you’re a beginner or could just use a refresher, we’re going to walk you through the process for a perfect bandsaw blade adjustment setup every time, no matter what blade you install. There is a whole quality spectrum when it comes to bandsaw blade guides. Lower the upper blade guide, open the wheel housing(s) and blade guard and carefully remove the blade. If you’re swapping to a different blade of the same width – perhaps to a higher tooth count – or putting the same blade back on, you may be able to get away without readjusting the guides. So it should be no real shocker that you’ll encounter conflicting schools of thought regarding blade placement on the wheels and how it affects blade “Drift”. On others, the thrust bearing is a “thrust block” instead. Either way, it serves the same function: supporting the blade as you feed material and preventing the blade from bowing and twisting as you exceed its beam strength. Will The Real Bandsaw Blade Guides Please Stand Up? While the guide assemblies can be generically referred to as “the blade guides”, the actual blade guides are the parts that sit to the left and right of the blade and restrict side to side movement and twisting.
how to put blade on bandsaw Related Question:
Why does my bandsaw blade keep falling off?
Blade Tension Is Too Loose The most common reason why the blade is slipping off is that there isn’t enough tension to keep it on. Blades can slowly become loose after years of wear and tear, and eventually, you’ll need to tighten or replace them.
How tight should a sawmill blade be?
For carbon steel toothed blades (cutting blades) this is typically 15,000 to 25,000 PSI. Slitting type blades typically are tensioned in the range of 12,000 to 20,000 PSI. In general bandsaw blades are never tensioned past 35,000 psi.
How is a band saw blade tracked?
Tracking describes the in-plane “front-to-back” motion of a bandsaw as it runs on the bandmill wheels. Bandsaw tracking stability returns the sawblade to its initial position after any in-plane side-to-side displacement caused by a cutting force.
Which way does a bandsaw blade go?
On a typical wood or metal cutting blade the hook or of point of the blade should be pointing down for a vertical blade bandsaw, or for a horizontal blade saw the hook of the teeth should be pointed such that they enter the workpiece first as the blade moves.
Are bandsaw blades universal?
Bandsaw blades differ in thickness, width, length, and tooth configuration. Length varies by machine, but the size of your saw’s wheels typically determines thickness and width: Smaller machines (9–12″ wheels) need thinner blades to prevent breaking the welds. They also accept only narrow blades, often 1⁄ 2 ” or less.
How do you break in Ellis saw blade?
To break-in your new blade, run it at the recommended speed but at only 1/3rd of normal pressure for ten minutes. Then gradually increase the pressure back to normal using the hydraulic cylinder.
Why won’t my bandsaw cut straight?
Band Saw: Why won’t my band saw cut straight? When the band saw cuts crooked, a dull blade, improper feeding, loose blade tension or not using a work piece guide could be the cause. Use the rip fence or miter gauge to guide the work piece uniformly through the cutting blade to make straight cuts.
What causes bandsaw blade drift?
Drift is cause because the blade buckles under the load. You can see that by stretching a ribbon between 2 points and applying a pressure to one of the edges, it will turn sideway easily. A sharp blade and high blade speed will help a lot with that.
How long should a bandsaw blade last?
On average your bandsaw blade should last 6 months to as long as a few years depending on what your cutting with it. Make sure to match your blade strength and quality to the project and material your cutting.