Find an old socket, grind it to fit, and use a light touch with a impact or hammer. It’s only $27, why snivle about the small amount to have the proper tool around.
Following are the steps that you need to follow to remove the chainsaw clutch without tool. Step 1: The first thing that you need to do is to remove the clutch cover, clutch bar and chain from the saw. Now if you intend to replace the old and broken clutch of the chainsaw with a new and better one, then all you need to do is follow this whole process reversely, and you will be able to get on the original clutch of the chainsaw.
Learning how to replace a chainsaw clutch and sprocket is a relatively quick and easy job that anyone can do. Learning how to replace a chainsaw clutch that’s broken is a pretty easy task. Either way, if you follow these simple steps you should be able to replace a chainsaw clutch and sprocket in about an hour or less without using any specialized tools.
how to remove chainsaw clutch without tool Related Question:
Can you start a chainsaw without a clutch?
A clutch is an absolute necessity on a chainsaw. Without one, the chain sprocket would be connected directly to the motor, and the chain would turn even when the engine is idling.
How does a primary clutch puller work?
The puller’s threads are farther back and a larger diameter, it threads into the clutch, and the longer unthreaded portion in front of it pushes up against the crank. As you tighten the puller, it pushes harder against the crank until the clutch pops free.
Are chainsaw clutches reverse thread?
The clutch bolt of the Husqvarna 55 chain saw is a “left-handed” or a reverse threaded bolt, meaning you turn the bolt clockwise to loosen it. This is the opposite of convention that teaches counterclockwise loosens.
Why is my chainsaw clutch slipping?
Clutch Wear Eventually, the lining becomes too thin to do its job, and the clutch begins to slip. This happens for two reasons. One is that the lining becomes so thin that the shoes don’t make complete contact with the drum, and the other is that the surfaces of the shoes become slippery.
Can you start a chainsaw with a cordless drill?
NOTE: A battery-powered drill is often not enough to start your chainsaw fast enough. In that case, use an electric drill plugged in a wall outlet. Sometimes the bolt will strip out and when you crank up, the bolt can come out.
Why is it so hard to pull start my chainsaw?
If your chainsaw is hard to pull, here are some common causes: The pully system is snagged or stuck. The starter assembly is stuck or sticky. The housing may be damaged.
Can you start a chainsaw with no chain?
It is not recommended to run a chainsaw without a chain. If you need to run it as a movie prop or you are fixing the engine, ensure that you run it for a short time only. I do not recommend letting it run for more than 5 minutes. Without a chain, the chainsaw will cause the engine to rev higher.
What size thread is a Polaris clutch puller?
3/4″ – 16 thread, 10 1/2″ long. Similar to Polaris # 2870506.
How do you know if your chainsaw clutch is bad?
Does the engine loose revs, or the engine keep revving and just the chain stops? If the engine is still running at normal revs, and the chain slows down, then it’s a problem with the clutch. Worn out, gummed up, jammed springs etc. If the engine looses revs under load then it’s more likely a fuel or carb problem.
What is a chainsaw sprocket?
What is the drive sprocket? The drive sprocket and the clutch drum are connected to the saw motor. The sprocket is designed to drive the proper-pitched chain around the guide bar.
What is a clutch puller?
Clutch Puller. Removes drive clutches on Polaris Side x Side and Snowmobile. Snow Applications: 700/800 XCR Fuji 3 cylinder engines 1999-2001, all Domestic twin 2 -strokes model year 2000 and newer, FS/FST models 2006 and newer. Side x Side Applications: Ranger RZR XP 2011 & newer. 3/4-16 thread.
What does a secondary clutch do?
The secondary clutch is mounted to the input shaft of the transmission, transaxle, or the like. In modern CVT systems such as those used in recreational vehicles, the secondary clutch has two functions: as a “slave” to the primary clutch and to provide a torque sensing element.
What is use of clutch puller?
Used to remove the drive clutch off of the engines crankshaft.