08-18-2011, 10:30 AM. I would use a large drum sander and use it to take off small amounts per pass until the smooth surface is gained. We are doing this for the Stonewall Jackson Prayer tree………I have the 16/32 drum sander and will use it because sanding a slice will be much better as far a chipout with a sander, instead of a planer. If you can chainsaw your cookies pretty close, you can finish them off in either a wide belt sander or a drum sander.
Some wood will stress crack from heat buildup and leave deep fine multiple cracks that won’t sand out and you will have to recut the wood to eliminate them. E – Most bowls are turned with the wood grain at a right angle to the lathe bed which means that 70% of what you are sanding is end grain. Save time! Start with a coarser grit than you think you need and sand with it longer than you think you need to, until all tooling marks and damaged wood fibers have been removed, then the rest of the job will go quicker and be more satisfying.
For faster hand sanding, you just press harder and move faster. Sanding faster comes at a price, of course: Six-inch sanders are two to three times more expensive than five-inchers, and the larger sanders are a little harder to control, especially on vertical or narrow parts. How to use a sander: Sand across the grain Smooth large areas fast.
how to sand out chainsaw marks Related Question:
How do you remove saw marks from wood?
“If burns do show up, you can remove them with a hand plane or a sharp scraper in addition to sandpaper on a sanding block.” Answer from Lee Grindinger: “Sure there is, a scraper or plane will make quick work of the burn marks.
Can you sand out burn marks?
Steps: Start by sanding down the area around the burn mark in the direction of the grain using 150-grit sandpaper until bare wood is visible again and the burn mark disappears. Sand a decent area around the burn mark to ensure that the floor doesn’t end up being too deep in the one area just around the mark.
Why is my chainsaw leaving burn marks?
Sharpening the chain to prevent the chainsaw from heating up and burning the wood. When you notice that the wood is burning, it is also possible that the chain is not sharp enough. This phenomenon is explained when you have repeated use of the equipment and unfortunately on your side you have never done its maintenance
Will paint cover sanding marks?
If the surface shows a relief or roughness, the only option will be to repair the affected area from scratch, preparing the intermediate coat again and applying the finish paint. This will prevent the appearance of sandpaper marks.
How do you remove sand scratches from wood?
A bit of clear nail polish dabbed across the scratch can remove the scratch. After it’s dry, lightly sand the treated area to even out the surface with 600-grit sandpaper. Buff the surface with a paste wax to complete the repair.
Do you have to sand wood with the grain?
No matter what type of edge you’re going for, always maintain steady pressure and sand with, not against, the grain. Don’t employ sandpaper to remove things like pencil marks or dried glue, but do use it to smooth joints or filled nail holes.
Can you sand rough sawn wood?
In order to sand rough cut wood slabs, start with 40 grit sandpaper and work in 2 foot by 2 foot sections. First, sand horizontally across the wood grain. Next, sand vertically with the grain. Then, sand in a 1 foot circular pattern with the grain.
How do you smooth rough wood without sanding?
Sand and a piece of leather or cloth, Pumice (a porous vulcanic Rock), Walnut Shells, Rottenstone (similar to Pumice), Wood Shavings, Corn Cobs, a Wood File, Scraping, Burnishing, or even building a primitive sanding tool are good alternatives to sandpaper.
How fine should you sand wood before staining?
For “hard to stain” woods, finish sanding with 120 grit will usually accommodate the problem. For finish sanding on most furniture hardwoods (e.g., cherry and mahogany) use 180 grit or 220 grit. The use of grits up to 600 is certainly allowed but is not standard practice.
How do you cut a chainsaw smooth?
You could use a router w/ a flat bottom bit and build a slead for it out of some staright boards and plywood then build a frame that you set the slead on and put the wood in and slowly go over it taking a little off at a time then lower the bit down until it is flush then ROB it smooth.
How do you get rid of burn marks?
To use this remedy, you need to remove the outer layer of the aloe vera leaf and take out the sticky gel from the inside of the leaf. Massage the gel on the skin and let it stay for 20-40 minutes. After this, wash off with water. You can even use coconut oil and aloe vera gel together to remove burn marks.
How do you get rid of burn marks on Oak?
Mix 1 tablespoon (approximately 20ml) of toothpaste with 2 tablespoons of baking soda (40ml) in a small bowl, creating a sticky white paste. Rub the paste into the heat mark in the direction of the wood grain.
What do burn marks on the stock and sawdust buildup on the blade indicate?
If you see burn marks on the cut edges of wood after you cut them with your table saw, it is because excessive heat from the saw blade is scorching the stock as it passes through the wood.
Why is my chainsaw blade smoking?
This most commonly is a result of a dull chain and exerting to much pressure on the bar and chain trying to make the chain saw cut. This could also be either a lack of bar and chain oil ( tank empty, restricted oiler hole ) or an inferior type of oil that is being slung off the chain and not lubricating.
How do you know when your saw blade is dull?
Look for worn-down, chipped, broken and missing teeth or chipped carbide tips that indicate it’s time to replace a circular saw blade. Check the wear line of carbide edges using a bright light and magnifying glass to determine if it’s beginning to dull.