Logan has some great tips and techniques for turning smaller logs into usable boards using the band saw in your shop. “Making Boards. After cutting the reference faces, you can start making boards. How you plan to use the wood will determine how thick to cut the boards. Keep in mind that the wet, rough-cut boards may warp and shrink. So don’t cut the pieces to the final thickness. Instead, I like to leave some extra material to allow for jointing and planing the wood smooth and flat once it’s dry. Adding about a 1⁄4” is a good rule of thumb. Freshly cut lumber needs to be stored and dried properly to end up as stable boards.
George Vondriska provides tips on how to formulate the board foot measure of hardwood so that you can better assess how much wood you’ll need for your woodworking project and better communicate with the salesman when you go to purchase your wood. George Vondriska demonstrates how to use an Epilog laser engraver to cut templates and inlays in your shop. George Vondriska provides tips on how to use a backyard saw mill to cut lumber from logs for your woodworking projects.
This will keep the log from rolling, rocking, or otherwise moving as it passes through the saw. Depending on the thickness of the log you do this process on your band saw, or move to your table saw. The band saw will slice larger logs and leave a smaller kerf, while the table saw will leave a smoother finish.
how to saw a log on a bandsaw Related Question:
How do you cross cut a log?
The basic technique is to start with a meeting cut through one third of the log from the side that is exposed to compressive stress – that is the side where you expect the guide bar to pinch. Then continue to cut a meeting cut on the opposite side until the log is cut through.
How do you cut thin wood slices?
To cut your wood slices, we strongly recommend you have either a miter saw or band saw. These are the best saw options to use when cutting log slices, as they can make more precise cuts with the uneven nature of a log. They can also cut thicker pieces of wood than other types of saws.
How do you cut wood for logs?
Similar to cant sawing, plain sawing begins with rotating and sawing the outer sides of a log into boards until the center is squared into a four-sided cant. Instead of leaving the cant as is, it is rotated and sawn to produce the maximum amount of lumber.
How thick of wood can a band saw cut?
Band saws are the undisputed champ when it comes to cutting curves and slicing through thick material. Many small band saws can slice though lumber a full four inches thick, and bigger saws handle six-inch cuts.
Can you cut logs with a hand saw?
The blade in a bush saw twists easily, so you can go off course while cutting and end up making a long crooked cut through a log. Try to use as much of the length of the blade as possible while cutting without overly bending your arm.
What saw is best for cutting logs?
A circular log saw is a stationary saw that is used to cut logs down to size to make firewood. Relatively simple in terms of design, all log saws work in more or less the same way. An electric motor or a petrol engine drives a circular saw blade which can vary in size from around 40 cm (15.7″) to 70 cm (27.5″).
How can I cut firewood without a chainsaw?
Even though a jigsaw is too weak to fell a tree or cut down large tree logs, you can use it to cut scrap wood like straight planks or pallets into firewood. The jigsaw comprises an electric motor and a reciprocating blade thus the better choice compared to using your hands or feet.
What is cross-cutting timber?
In woodworking, a rip-cut is a type of cut that severs or divides a piece of wood parallel to the grain. The other typical type of cut is a cross-cut, a cut perpendicular to the grain. Unlike cross-cutting, which shears the wood fibers, a rip saw works more like a series of chisels, lifting off small splinters of wood.
What is a ripping chain?
Ripping chain is chainsaw chain designed specifically for cutting with the grain. Ripping chain is always micro chisel or semi chisel chain which features a re configured cutting angle of 10 degrees.
What is a chainsaw cross cut?
The cross-cutting technique helps to prevent your chainsaw chain and bar from becoming trapped or damaged when felling a tree. By making the first cut when using this technique, you are effectively displacing the tension and preventing any accidental splits from occurring.