As the name suggests, a depth gauge is a part of the cutter tooth that controls the depth of the cut. I will show you first how the depth gauge affects the cutting efficiency of your chainsaw. While the cutter teeth have been filed, it is also important to adjust the depth gauges to compromise our cutting depth.
PLACEMENT Place one of the holes in the gauge over one of the depth gauges on the chain. Let the gauge sit against the cutting tooth behind it. HOLD THE GAUGE FIRMLY IN ONE HAND Hold the flat file in your other hand and file the depth gauge until the file comes in contact with the gauge.
how to set chainsaw depth gauge Related Question:
What does a depth gauge on a chainsaw do?
A depth gauge is used to provide a flat surface across the teeth of your chainsaw’s teeth to provide a guideline for filing them down to the same height. Step 1: Place a round file on a tooth on the left hand side and, holding it at a 45 degree angle, pull it in a single direction across the tooth.
Are all chainsaw depth gauges the same?
A: When depth gauges are uneven, each cutter tooth on the chain takes a different sized bite. This causes the chain to cut rough and vibrate. If the depth gauges are higher on one side than the other, this causes the chain to cut crooked. The cut will pull in the direction of the side that has the lower depth gauges.
What happens if you file rakers too low?
If the rakers aren’t at the right depth, your saw won’t self-feed and you’ll find yourself pushing down on the saw as you cut. That not only wears you out, but it wears out the bar and chain as well.
How do you measure depth accurately?
The depth micrometer is an accurate and reliable tool to use for depth measurement (Figure 1). The depths of holes, slots, shoulders, and projections can be measured accurately to within 0.001 of an inch. When using a depth micrometer, two points must be kept in mind.
How do you know what file to use on a chainsaw?
Simply put, the type of chainsaw file you need directly corresponds with the size of your chain pitch. The larger the pitch will mean the higher the cutting teeth will be. The higher the teeth will therefore mean the larger the file will need to be.
What angle do you file a chainsaw chain?
STIHL saw chains are generally filed to an angle of 30° – parallel to the service mark for the filing angle. Hold the file so that one quarter of its diameter projects above the top plate.
Does cutting wet wood dull a chainsaw?
Does Cutting Wet Wood Dull a Chainsaw? Using your chainsaw to cut through wet wood will not dull the chain any faster than using it for other types of wood. When you think about it, your chainsaw chain is already wet. True, it is not wet with water.
Why does my chainsaw chain dull so quickly?
Dirt Causes A Chainsaw To Dull If you’re cutting through logs and your angle of approach is too steep, a simple cut through could nick dirt or even worse, rocks on the floor causing your chainsaw to jerk, thus dulling.
How high should the rakers be on a chainsaw chain?
The raker should be about 0.50. 8 mm lower than the cutter. You sharpen the cutters first. Lay the file gauge on the chain.
Why does my chainsaw pull to the left?
One major reason a chainsaw curves to either the right or left during a cut is that it was unevenly sharpened. The unequal teeth of the chain cause it to take a different-sized bite into the wood. What is this? The uneven sharpness of the chain is mainly due to manual sharpening, especially with the use of a file.
What is chainsaw pitch and gauge?
Pitch and gauge of the chain. * Pitch is the distance measured on center of any three rivets in a row. This distance will most commonly be 1/4″ . 325″ or 3/8″. * Gauge is the width of the groove in the bar that the chain rides in.
What is the measurement shown on the depth gauge?
A depth gauge typical refers to is a precision measurement instrument that is used by mechanical engineers, manufacturing engineers, and machinists among others, to accurately obtain the measurement of the depth of a bored cavity, recess, hole, groove or other similar openings that were created below the surface level
What is the difference between Gage and gauge?
Gage is the spelling of an obsolescent word meaning a pledge, a challenge, etc. Gauge is the spelling to use when you measure measurement, estimate, or standard.
What is Vernier depth gauge?
Vernier depth gauge is used for measuring the depth of holes, recesses and distances from a plane surface to a projection. Here the graduated scale is slide through the base and vernier scale remains fixed.
What rule is used to measure the depth of a small diameter hole?
Depth Gages are an adaptation of the rule or Vernier scale for measuring the depth of holes, recesses, etc.