Determine the blade depth by unplugging the saw and holding it alongside your board with the blade guard retracted. Use only the Makita wrench to install or remove the blade. Purchasing a diamond blade for your 7″ circular saw can be an ample investment, but you can be sure that it will outlast an abrasive-type blade – it’s a perfect choice for those that cut a lot of concrete.
In this Circular Saw 101 video, This Old House contributor Mark Clement demonstrates how to adjust the depth of the blade on your circular saw to maximize its potential. Learn how to safely operate the tool, avoid excess friction, and create a cleaner cut by correctly setting the saw and adjusting the blade’s depth.
If you don’t have a table saw handy, and the rip cut doesn’t have to be precise, then a circular saw works fine. Then align the saw with your mark and let gravity help pull the saw through the cut. Making long narrow rip cuts with a circular saw is easy if you use your index finger as a guide.
how to set depth on makita circular saw Related Question:
How do you adjust the depth on a Makita circular saw?
Loosen the lever on the depth guide and move the base up or down. At the desired depth of cut, secure the base by tightening the lever. For cleaner, safer cuts, set cut depth so that no more than one blade tooth projects below workpiece.
How do you adjust the blade depth on a circular saw?
Determine the blade depth by unplugging the saw and holding it alongside your board with the blade guard retracted. Then loosen the depth-adjusting lever or knob and pivot the saw’s base until the blade extends about 1/4 to 1/2 in. below the board. Tighten the lever or knob and you’re ready to saw.
How do you adjust the height on a Makita circular saw?
A circular saw has a depth adjustment lever or knob that releases or loosens to allow for adjustment of the saw’s bottom plate, often called the “shoe.” First unplug your saw, then disengage this lever so that you can freely adjust the cutting depth by raising or lowering the bottom plate.
How far down do you set the circular saw cut depth?
Don’t clamp both sides of a cut. For efficiency and safety, set the blade depth no more than 1/4-inch below the thickness of the board.
What is the bevel adjustment on a circular saw?
Circular saws commonly include an adjustment that allows you to set the blade angle anywhere from zero to 45 degrees. Using this feature, you can cut a bevel along the length of a board and a miter across the end.
How do you unlock a Makita circular saw?
To lock the lock lever, push it down and turn it 90° counter- clockwise. To release the lock lever, turn it 90° clockwise.
What is the closest you should put your fingers to the blade while it is running?
Do not put your fingers closer than two inches from the blade. 3. Do not place your hands directly in line with the blade while cutting stock. 4.
Why is my circular saw binding?
A circular saw binds because of failure to ensure proper blade depth; setting the blade too deep presents a danger because more blade surface is exposed while cutting than a properly set blade. When the saw is too deep, kickback and binding will be inevitable.
Why won’t my circular saw cut all the way through?
Here are some reasons your circular saw keeps stopping: Make sure your work piece is properly supported so it doesn’t pinch the blade which could also cause kickback in addition to stopping. Damaged, warped, loose or dull blade. Motor malfunctioning or overheating. Cable problems like frayed cord or weak connection.
How deep can a 5.5 circular saw cut?
It turns out that it’s a simple question but very essential when you are going to do a project using this kind of saw. To sum up, a standard circular saw can offer a cutting depth of 2.5 inches as the maximum, but you can adjust the depth to match your requirements.
Why are my circular saw cuts curves?
Check whether the blade is parallel with the edge of the base, the edge that goes against the guide. If the blade is further away at the front, it’s going to want to walk away from the straight-edge. This is probably easiest to do when the base is in the 90 degree position rather than set at a bevel.
Why does my circular saw cut crooked?
The nuts and screws that hold the blade of a circular saw can become loose when the saw is used for a long time. The blade may also become misaligned. Tip: If the blade is wobbling because of loose nuts and screws or improper alignment, you should fix it appropriately. A properly fixed blade will not wobble as you cut.
Why won’t my miter saw lift up?
The blade should lift up automatically when the pin is released. The guard should cover the blade as it lifts. If it doesn’t, it’s likely dirty or stuck and should be cleaned to move freely with the blade.
How do you lubricate a sliding miter saw?
Apply a small amount of spray lubricant onto the blade of the saw and spread it out over the blade by hand. Let it soak in and wipe off any excess with a clean rag. Drop the blade guard back over the blade.
How deep can you cut with a 7.25 circular saw?
Circular saw sizing is based on the blade diameter. Standard-size saws use 7 1/4-inch blades and can cut a maximum depth of about 2 1/2 inches.
