Install the blade and apply just enough tension to keep the blade securely on the wheels. Instead, tension the blade until your finger is only able to deflect the blade by about 1/4″. This test should be done at the back of the saw where nothing can get in the way of the blade. After the tension is set, make sure the blade is still tracking properly with the gullet in the center of the top wheel. You don’t want the side guides to contact the cutting teeth of the blade since the teeth flare out at a slight angle. Adjust the thrust bearings carefully so that they do NOT rotate while the blade moves, but they DO begin to rotate as soon as light pressure is applied to the blade. Just like the thrust bearing adjustment, the side guides should be as close to the blade as possible without actually touching. Turn the saw off, flip the board around and try to get the blade to slide into the cut slot.
A bandsaw will only cut accurately if the blade guides are set correctly, so these are important. Some people have the bearings touching, others don’t, we tend to side with the latter and like them to be set around 0.5mm either side of the blade. Simply place the Buddy up against the blade, using the recess to counter the tooth set.
Even a low-end bandsaw blade tension meter can cost $300. If you use your bandsaw a lot or are doing delicate work, having the proper tension on the blade can be critical and the only way to accomplish this is with a bandsaw blade tension meter. With the bandsaw blade properly installed, and tensioned, and the blade guides properly set, the next issue is to make sure that the bandsaw table is square and level. We suggest that you go through the setup steps in this how to set up a bandsaw properly: the ultimate g guide before starting a new project and each time you change your bandsaw blade.
how to set up a new bandsaw Related Question:
How close do you set the side guides on the band saw?
The front of the side guides should be located about 1/16″ back from the deepest part of the blade gullets. You don’t want the side guides to contact the cutting teeth of the blade since the teeth flare out at a slight angle. This adjustment is made to both the top and bottom guides.
Which way should the teeth face on a bandsaw?
The teeth on the bandsaw blade should face down so that the cutting action is from the top of the material to the bottom.
How long should a metal cutting bandsaw blade last?
On average your bandsaw blade should last 6 months to as long as a few years depending on what your cutting with it. Make sure to match your blade strength and quality to the project and material your cutting.
What is blade Break?
When you break in a blade, you wear off the sharp pointed edge on the blade teeth and form a small rounded tip. This small radius will be able to better withstand the cutting pressures of sawing and will deliver more consistent cutting results.
How tight should my bandsaw blade be?
The blade should deflect no more than 1/4 in. A good place to begin is to tension the blade until the meter reads proper tension for the next wider blade. For example, if you’re tensioning a 3/8-in.
Why won’t my bandsaw cut straight?
Band Saw: Why won’t my band saw cut straight? When the band saw cuts crooked, a dull blade, improper feeding, loose blade tension or not using a work piece guide could be the cause. Use the rip fence or miter gauge to guide the work piece uniformly through the cutting blade to make straight cuts.
Can you put a bandsaw blade on upside down?
Typical bandsaw blades can be flipped “inside out” to make the teeth point the other direction. On some knife edge style blades and grit edge blades you can get a fresh sharp cutting edge from a blade this way, just by flipping it inside out.
What is the purpose of the blade guides on a bandsaw?
Bandsaw blade guides keep the bandsaw blade on track while cutting through materials. Blade guides should be set above and below the saw table to help reduce vibration by holding the bandsaw blade in place while cutting. This assures a precise and quality cut.
Why is my bandsaw burning the wood?
A majority of issues with wood burning is because of a dull saw blade. These blades may not be sharp enough to efficiently cut the wood, and thus create enough friction to heat and burn the wood. What is this? Dull blades make it more challenging to cut, which causes friction as you pass the wood through.
Are bandsaw blades worth sharpening?
Since a carbide-tipped bandsaw blade will cost well over $100, spending a third of the cost of the blade (or more) to get it sharp and working like new again can make financial sense. However the majority of bandsaw blades, the Wood Slicer included, are not worth spending money to have sharpened.
How many times can a bandsaw blade be sharpened?
It often makes sense to replace a dull blade with a new one, but you can sometimes get the best value out of merely sharpening an old blade instead of replacing it altogether. You should typically be able to get two to three sharpenings before you need to change your blade completely.