Install the blade and apply just enough tension to keep the blade securely on the wheels. Instead, tension the blade until your finger is only able to deflect the blade by about 1/4″. This test should be done at the back of the saw where nothing can get in the way of the blade. Adjust the thrust bearings carefully so that they do NOT rotate while the blade moves, but they DO begin to rotate as soon as light pressure is applied to the blade.
Even a low-end bandsaw blade tension meter can cost $300. If you use your bandsaw a lot or are doing delicate work, having the proper tension on the blade can be critical and the only way to accomplish this is with a bandsaw blade tension meter. With the bandsaw blade properly installed, and tensioned, and the blade guides properly set, the next issue is to make sure that the bandsaw table is square and level. We suggest that you go through the setup steps in this how to set up a bandsaw properly: the ultimate g guide before starting a new project and each time you change your bandsaw blade.
Whether you’re a beginner or could just use a refresher, we’re going to walk you through the process for a perfect bandsaw blade adjustment setup every time, no matter what blade you install. Lower the upper blade guide, open the wheel housing(s) and blade guard and carefully remove the blade. So it should be no real shocker that you’ll encounter conflicting schools of thought regarding blade placement on the wheels and how it affects blade “Drift”.
A bandsaw will only cut accurately if the blade guides are set correctly, so these are important. Some people have the bearings touching, others don’t, we tend to side with the latter and like them to be set around 0.5mm either side of the blade. Simply place the Buddy up against the blade, using the recess to counter the tooth set.
The first thing you need to do is install the blade. Remember, do not push too hard but rather adjust the amount of pressure and monitor the blade tracking. A known fact is if the blade slides in the cut slot easily, the table is 90 degrees to the blade.
A catalyst for this seems to be Jim Cummings article “Home Shop Bandsaw” in Fine Woodworking #63. From the hundreds of bandsaw owners I’ve talked with since the article appeared, it seems there are lingering questions on how to adjust a bandsaw blade, the blade choice and operation. “To find the correct tension, you can start with the tension scale on your saw, but you will probably need to fine tune the adjustment. With the saw unplugged, increase the tension on the blade until pushing on the side of the blade with your finger using a moderate amount of force deflects the blade about a 1/4” from its normal position. An interesting experiment is to set the side guys too far from the blade and notice how increased feed pressure and turning make the blade wander.
how to set up bandsaw blade Related Question:
Where should a bandsaw blade sit on the wheel?
Make sure the machine is disconnected from the power supply. When tracking, you always want to make sure that the blade is sat on the crown of the wheel, with the deepest part of the gullet in the centre.
How close do you set the side guides on the band saw?
The front of the side guides should be located about 1/16″ back from the deepest part of the blade gullets. You don’t want the side guides to contact the cutting teeth of the blade since the teeth flare out at a slight angle. This adjustment is made to both the top and bottom guides.
How tight should my bandsaw blade be?
The blade should deflect no more than 1/4 in. A good place to begin is to tension the blade until the meter reads proper tension for the next wider blade. For example, if you’re tensioning a 3/8-in.
Why won’t my bandsaw cut straight?
Band Saw: Why won’t my band saw cut straight? When the band saw cuts crooked, a dull blade, improper feeding, loose blade tension or not using a work piece guide could be the cause. Use the rip fence or miter gauge to guide the work piece uniformly through the cutting blade to make straight cuts.
How high should a band saw table be?
For the small shop furniture maker, go with 14″ as the minimum for a bandsaw, though 16″ is better. Those doing larger work might even want 18″ or 20″ machines. Just make sure you have a minimum resaw height of 12″ for versatility.
Why is it important to adjust the height of the blade guard on the bandsaw?
Adjust blade guard height to about 3 mm or 1/8 inch to 6mm or 1/4 inch above the top of the material being cut. Wider gaps will place tension on the blade and increase the risk of breaking. Ensure the blade is tracking correctly and runs freely in and against the upper and lower guide rollers.
Can you put a bandsaw blade on upside down?
Typical bandsaw blades can be flipped “inside out” to make the teeth point the other direction. On some knife edge style blades and grit edge blades you can get a fresh sharp cutting edge from a blade this way, just by flipping it inside out.
What is the gullet on a bandsaw blade?
Bandsaw blade gullets are the space or curvature between each individual tooth on a saw blade. With each pass of the blade, the material being cut will curl into the gullet, creating a spiral of material called the chip. Too many teeth in the cut will make the gullet full.
What is the purpose of the blade guides on a bandsaw?
Bandsaw blade guides keep the bandsaw blade on track while cutting through materials. Blade guides should be set above and below the saw table to help reduce vibration by holding the bandsaw blade in place while cutting. This assures a precise and quality cut.
Why did my bandsaw blade snap?
Machine Defects Even the best blades can fail if there is something else wrong with your bandsaw, and even a small misalignment of bearings or guides can put a twist in the blade as it goes around. Resulting in tension being applied in all the wrong ways which will lead to early breakage.
Why are my bandsaw cuts wavy?
Re: Band saw Cutting Wavy Cuts. The clasic cause for wavy lumber is pushing a dull blade past it’s limits. Sharp don’t get it.
Which way should the teeth face on a bandsaw?
The teeth on the bandsaw blade should face down so that the cutting action is from the top of the material to the bottom.
Why does my bandsaw blade wobble?
The blade on a saw left idle for long periods of time can leave an impression in the rubber tire which might cause erratic tracking. Purchase and install aftermarket replacement tires. (Search for “bandsaw tire” at woodcraft.com.) If you still see a back-and-forth motion, the culprit is probably the wheel itself.