How to Start a Chainsaw That’s Been Warmed Up.If you’re taking a short break from using the chainsaw, then you can restart it without using the choke since the engine is already primed with fuel. If you haven’t purchased a chainsaw yet, I encourage you to take a look at my best gas chainsaw reviews. Check out my best 18 inch chainsaw page and best 16 inch gas chainsaw page to see what you can get.
In this blog post, I will discuss the four best alternatives to crank start the engine of your chainsaw without pulling the cord or make it start easier. If the engine of your chainsaw is not convertible from cord start to an electric start then you can start it with an electric drill. If your chainsaw has a Tecumseh engine, for example, you may or may not be able to turn it from a manual pull cord start to an electric start.
To clear excess fuel from the carburetor, place the choke lever in the Off position, hold the throttle trigger fully open and pull the starter rope 5 or 6 times. Try to start the chainsaw after priming the carburetor. Activate the choke by moving the lever to the full choke position and pull the starter rope 3 or 4 times to start the engine.
how to start a chainsaw easy Related Question:
How do I make my chainsaw easier to start?
Try to start the chainsaw after priming the carburetor. 5. Activate the choke by moving the lever to the full choke position and pull the starter rope 3 or 4 times to start the engine. If that doesn’t work, move the choke lever to half choke and pull the starter rope, 6 times maximum, to start the engine.
Why is it so hard to pull start my chainsaw?
If your chainsaw is hard to pull, here are some common causes: The pully system is snagged or stuck. The starter assembly is stuck or sticky. The housing may be damaged.
What is the easiest to start chainsaw?
The best gas-powered model, the ECHO 18 in. Gas 2-Stroke Cycle Chainsaw, is easy to start and has impressive cutting power.
Can you start a chainsaw with a cordless drill?
NOTE: A battery-powered drill is often not enough to start your chainsaw fast enough. In that case, use an electric drill plugged in a wall outlet. Sometimes the bolt will strip out and when you crank up, the bolt can come out.
How do you rewind a chainsaw pull start?
Feed the cord through the holes in the housing and pulley, and tie a knot in the end. Keep tension on the cord with one hand while you release the pliers with the other. Let the pulley slowly rewind. It will wrap the cord around itself and stop when the handle contacts the housing.
What causes a chainsaw to vapor lock?
Vapor lock occurs when the fuel (usually gasoline) within the fuel delivery system overheats and vaporizes too rapidly. The resulting excess gas bubbles accumulate to the point of actually blocking normal fuel delivery.
How long does it take to Unflood a chainsaw?
The first option is the easiest since it doesn’t require any effort on your part, it just takes time. Many people wonder if a flooded chainsaw will fix itself? The answer is yes, but not always. By letting the chainsaw sit for about 20 minutes it will allow some of the fuel inside the engine to evaporate.
Do you start a chainsaw with the brake on?
The chain brake should be activated when you start the chainsaw. Many chainsaw models can be started in what is known as ‘half-throttle’ position. In this position, the chain can rotate – if the chain brake is not activated.
Why can’t I start my Stihl chainsaw?
Dirty or clogged fuel tanks, dirty fuel filters and lines, loose fuel hoses, dirty air filters and a dirty carburetor can all restrict fuel flow. Check, clean and replace all the fuel system parts before moving into the internal engine, as gas problems create a majority of starting problems.
How long does a spark plug last in a chainsaw?
A poorly functioning engine in a Stihl chainsaw can mean more work for the operator and can even be dangerous. Consequently, Stihl recommends replacing the spark plug after every 100 service hours.
Can you start a chainsaw without the bar?
You can run a chainsaw without a chain, but I wouldn’t recommend this for more than a few minutes. The engine will rev up higher, and these increases wear and tear. It can also run hot when the throttle is used. Ensure that you empty the bar oil tank, else oil can spray out of the chainsaw.
Do they make an electric start chainsaw?
We hate to inform you, but gas chainsaws with automatic electric-start systems don’t exist. The mechanism that keeps the saw running—the gas engine—is the same mechanism that gives it the power to start. A special spring is probably the most common easy-start feature you’ll find on chainsaws.
How does a pull start work?
The operator pulls the rope’s handle or grip. This causes the rope to unwind around the crankshaft and spin it. The spinning motion of the crankshaft cranks the engine. The crankshaft’s motion engages the flywheel, enabling the engine to start.
How do I know if my chainsaw spark plug is bad?
If it’s not producing any sparks at all, your chainsaw needs a new plug. If there are only a few sparks coming out of one side of the electrodes but none on the other side, it’s not bad enough for you to worry about, but it will affect your performance.
Why does my chainsaw bog down when I give it gas?
If your chainsaw is bogging down when you give it throttle, this is often a sign of improper gas-to-oil ratio. If there is too much gasoline in relation to the amount of oil used, this is known as a “rich mixture” and can cause the chainsaw to run poorly.