If your chainsaw was sitting for a long period with gas in the tank, check out this post “Chainsaw won’t start after sitting”. A warm chainsaw may not need a choke to start but a cold saw won’t start without a choke. Obviously, new saws don’t have gas in the system and so the fuel lines are filled with air.
How to Start a Chainsaw That’s Been Warmed Up.If you’re taking a short break from using the chainsaw, then you can restart it without using the choke since the engine is already primed with fuel. If you haven’t purchased a chainsaw yet, I encourage you to take a look at my best gas chainsaw reviews. Check out my best 18 inch chainsaw page and best 16 inch gas chainsaw page to see what you can get.
The chain brake should be activated when you start the chainsaw. Release the front handle and allow gravity to bring the chainsaw down, rotating around the rear handle, towards the stump. Hold the chainsaw firmly by the front and rear handles.
how to start new chainsaw Related Question:
Why can’t I start my new chainsaw?
A fuel issue is one of the most common reasons why a chainsaw won’t start. If the operator has repeatedly been trying to start the chainsaw through the recoil starter system, they may have accidentally flooded the engine with fuel. A common indication the engine has been flooded is the smell of gasoline in the air.
Do you need to run in a new chainsaw?
Refrain from running your chainsaw at full throttle during its first three fuel tank fillings. Doing so will help to prevent heavy-duty workloads while the saw is within its break-in period. Your Stihl chainsaw engine will reach its maximum power after you have refueled its tank five to 15 times.
How long to wait if chainsaw is flooded?
Many people wonder if a flooded chainsaw will fix itself? The answer is yes, but not always. By letting the chainsaw sit for about 20 minutes it will allow some of the fuel inside the engine to evaporate.
Should you run a chainsaw at full throttle?
Engine Protection Generally, two-stroke chainsaw engines are built to conveniently run at full throttle without an engine breakdown. Therefore, running at any throttle speed below the full throttle is not advised.
How do I start my Stihl chainsaw for the first time?
Press and hold the throttle trigger lockout (located on the side of the chainsaw, above the trigger) with your thumb, then move the master control (on the left of the rear of the chainsaw) down as far as it will go. This is the position you should start the chainsaw in the first time you use it each session.
How long should you run a chainsaw?
Depending on the type and usage, you can expect a gas Chainsaw to run between 15 and 40 min before you have to fill it up again. Most battery-powered chainsaws have a run time of up to 2 hours, but there are high-capacity power packs that will last much longer.
How long does a spark plug last in a chainsaw?
A poorly functioning engine in a Stihl chainsaw can mean more work for the operator and can even be dangerous. Consequently, Stihl recommends replacing the spark plug after every 100 service hours.
Why is my Stihl chainsaw not starting?
Dirty or clogged fuel tanks, dirty fuel filters and lines, loose fuel hoses, dirty air filters and a dirty carburetor can all restrict fuel flow. Check, clean and replace all the fuel system parts before moving into the internal engine, as gas problems create a majority of starting problems.
Can you over prime a chainsaw?
If the engine will not start, the most likely failure is that your chainsaw has flooded due to over-priming of fuel or the choke has been left too open, causing too much fuel to enter the combustion chamber.
Will a flooded engine fix itself?
Will a flooded engine fix itself? No. You have to take appropriate measures to restore the fuel and air balance in your car’s engine.
How many pulls should it take to start a chainsaw?
With the choke in the “off” position, pull the engine’s crank cord through again. The engine should start in 1 to 3 pulls.
Can you run a chainsaw without a spark arrestor?
We can’t run without arrestors here, and the fire danger is so high I wouldn’t anyway. There is less restriction without it, but cleaning them from time to time helps a lot. If it’s hot and dry, I wouldn’t risk it.
What does a clogged spark arrestor do?
Sometimes the spark arrestor screen can become clogged up itself. Common symptoms include lack of power, especially under load; poor acceleration; engine won’t come up to full RPM; and higher than normal “spit back” through the carburetor.
How does a chainsaw ignition system work?
Electrical currents run through the ignition coil and transmit electricity to the spark plug. The electricity creates sparks within the spark plug, and the sparks ignite the fuel in the engine, enabling the chain saw to run. Testing the ignition coil at home is simple to do and requires minimal tools.
What should you not do with a chainsaw?
Don’t Cut With Improper Blade Tension A overly loose or tight chain also wears out the drive sprocket and causes rapid chain and bar wear. To determine if your chain is properly tensioned, pull up on the chain. The drive links should still be in the bar groove. If the links come out of the bar, the chain is too loose.