Tim Inman: Because band saw blades ride on crowned wheels, they always have a little “Camber” angle relative to the vertical axis of the wheel. Using a rip fence on a band saw, like a rip fence you might find on a table saw, will nearly always cause grief – especially when you try cutting long boards. Chris Marshall: A point fence works wonders! My band saw’s rip fence can also be adjusted for front-to-back blade drift, and I’ve actually had good luck using it for resawing once I adjust for the saw’s drift that day.
On a typical wood or metal cutting blade the hook or of point of the blade should be pointing down for a vertical blade bandsaw, or for a horizontal blade saw the hook of the teeth should be pointed such that they enter the workpiece first as the blade moves. During regular cutting on a well set up bandsaw the blade will move or bow backwards a bit as you press the workpiece into it. The side guides will assist in keeping the blade cutting straight, but they are not an iron lock on the blade forcing it to cut straight.
“Cutting tenons on a bandsaw seems like a fairly simple operation. Several woodworking articles have suggested the 1/4 x 6T blade for cutting tenons. Not sure why I can’t get these 1/4″ blades to cut straight. Since you only have this problem on the SS with a 1/4” blade I suspect the blade. “The first thing I did was replace the backup bearings. Next I aligned the fence to the miter slot. Once I had that squared away I then aligned the table to the bandsaw blade. To do that I used a new 3/8” blade and the Carter FAST jig to help better see the orientation of the blade.
I find it impossible to make a straight, linear cut with my bandsaw. I have to veer the wood off at an increasing angle to cut along a marked straight line. I’ve gotten good at this compensating, but it seems that it must not be adjusted correctly if I have to do that.
how to stop band saw blade wandering Related Question:
What causes a bandsaw blade to drift?
Drift is cause because the blade buckles under the load. You can see that by stretching a ribbon between 2 points and applying a pressure to one of the edges, it will turn sideway easily. A sharp blade and high blade speed will help a lot with that.
Why does my bandsaw mill blade wander?
When you’re sawing a soft wood with hard knots, the engine will slow down each time you hit a knot. If the blade speed drops below about 5000 FPM, the blade will start to wander. The governor will kick in to get the engine back up to speed but by the time that happens you’re through the knot.
Why does my bandsaw spark?
Ceramics can cause sparks. Or, if your thrust bearing is too far past the blade, more toward the center of the bearing than the edge, then it won’t turn and you’ll get sparks too, and possibly wear a groove in the bearing.
Why does my bandsaw blade burn the wood?
A majority of issues with wood burning is because of a dull saw blade. These blades may not be sharp enough to efficiently cut the wood, and thus create enough friction to heat and burn the wood. What is this? Dull blades make it more challenging to cut, which causes friction as you pass the wood through.
Why do I keep breaking band saw blades?
Even the best blades can fail if there is something else wrong with your bandsaw, and even a small misalignment of bearings or guides can put a twist in the blade as it goes around. Resulting in tension being applied in all the wrong ways which will lead to early breakage.
Why does my bandsaw blade wobble?
The blade on a saw left idle for long periods of time can leave an impression in the rubber tire which might cause erratic tracking. Purchase and install aftermarket replacement tires. (Search for “bandsaw tire” at woodcraft.com.) If you still see a back-and-forth motion, the culprit is probably the wheel itself.
Why does my saw blade smoke?
A Dirty Skill Saw Blade Can Cause Smoke When you use your saw repeatedly for an extended period, something called pitch can begin to coat the teeth of your blade. This pitch is rather sticky. As a result, it creates friction when cutting and possibly smoke.
How can I speed up my bandsaw?
Answer: Some models of bandsaws do provide the ability to alter the speed of the blade (usually expressed as FPM – feet per minute). The change of speed is usually accomplished by moving a drive belt to a secondary location on the pulley(s) of the drive pulley and motor pulley.