Band saw blade drift is a tendency of the blade to veer to the left or right while making a cut using the rip fence. The point of the last paragraph is that if the band saw is not set up properly and/or does not have a good quality, sharp blade installed and tensioned correctly, the chances of accurately adjusting for drift are minimal at best. Since there is little that we can do about blade drift at the blade, we adjust the fence to match the drift angle to essentially cancel it out.
Being a happy bandsaw owner has a lot to do with your approach to coping with the fact that a bandsaw simply will not cut straight, or, in the sage words of veteran woodworkers, “Adjusting for drift.” Even the top performing 14″ bandsaw on the market, Powermatic’s 14 Bandsaw 1791216K, comes with a no-frills fence with 4 bolts on top rather than easy and obvious thumbscrews or knobs that say, “Adjust me here!”. Making the bandsaw cut nice and straight with this fence is a snap.
There’s no doubt about it – a bandsaw is one of the tools in your shop that might cause you the most frustration. Every shop needs one, so whether you’re an amateur struggling with blade drift or a professional who is constantly searching for ways to improve your workflow, having a well-functioning bandsaw is worth it. No matter what size your bandsaw is, we offer the always-reliable Timber Wolf bandsaw blades that make perfect replacements and cost-effective upgrades.
The amount of drift varies with every blade, but you can compensate for it by clamping your fence to match the drift angle. SINGLE-POINT FENCE. Another way to overcome blade drift is to use a single-point fence like the one shown in the left photo above and in the margin. SETTING THE FENCE TO COMPENSATE FOR BLADE DRIFT. FEED RATE & TECHNIQUES. With either style of fence, your saw will help you determine the feed rate for resawing.
My playing around over the past few years seems to confirm the suggestion that presuming a correctly sharpened and jointed blade that can/has cut straight that the onset of drift is mostly to do with position of the blade on the tyres – that if a previously straight cutting blade starts to drift that it’s probably that the blade has moved on to a different part of the tyre. The other possibility is that something other than normal wear has happened to make the blade cut differently off one side than the other if a problem suddenly kicks in – but it should keep on tracking OK with normal even wear. Prime suspect with a new blade on a saw that has previously been OK has to be a misaligned weld, or a badly sharpened blade…. ian.
how to stop bandsaw drift Related Question:
What causes bandsaw blade drift?
Drift is cause because the blade buckles under the load. You can see that by stretching a ribbon between 2 points and applying a pressure to one of the edges, it will turn sideway easily. A sharp blade and high blade speed will help a lot with that.
What is drift on a bandsaw?
Most band saw blades tend to veer slightly to the left or right when cutting. This is known as blade drift. The amount of drift varies with every blade, but you can compensate for it by clamping your fence to match the drift angle.
How tight should my bandsaw blade be?
The blade should deflect no more than 1/4 in. A good place to begin is to tension the blade until the meter reads proper tension for the next wider blade. For example, if you’re tensioning a 3/8-in.
Why does my bandsaw spark?
Ceramics can cause sparks. Or, if your thrust bearing is too far past the blade, more toward the center of the bearing than the edge, then it won’t turn and you’ll get sparks too, and possibly wear a groove in the bearing.
Why is it important to adjust the height of the blade guard on the bandsaw?
Adjust blade guard height to about 3 mm or 1/8 inch to 6mm or 1/4 inch above the top of the material being cut. Wider gaps will place tension on the blade and increase the risk of breaking. Ensure the blade is tracking correctly and runs freely in and against the upper and lower guide rollers.
Why does my bandsaw blade keep falling off?
Blade Tension Is Too Loose The most common reason why the blade is slipping off is that there isn’t enough tension to keep it on. Blades can slowly become loose after years of wear and tear, and eventually, you’ll need to tighten or replace them.
What is the gullet on a bandsaw blade?
Bandsaw blade gullets are the space or curvature between each individual tooth on a saw blade. With each pass of the blade, the material being cut will curl into the gullet, creating a spiral of material called the chip. Too many teeth in the cut will make the gullet full.
How long should a bandsaw blade last?
On average your bandsaw blade should last 6 months to as long as a few years depending on what your cutting with it. Make sure to match your blade strength and quality to the project and material your cutting.
Is it worth it to sharpen bandsaw blades?
Since a carbide-tipped bandsaw blade will cost well over $100, spending a third of the cost of the blade (or more) to get it sharp and working like new again can make financial sense. However the majority of bandsaw blades, the Wood Slicer included, are not worth spending money to have sharpened.
How many times can a bandsaw blade be sharpened?
It often makes sense to replace a dull blade with a new one, but you can sometimes get the best value out of merely sharpening an old blade instead of replacing it altogether. You should typically be able to get two to three sharpenings before you need to change your blade completely.
Why is my bandsaw burning the wood?
A majority of issues with wood burning is because of a dull saw blade. These blades may not be sharp enough to efficiently cut the wood, and thus create enough friction to heat and burn the wood. What is this? Dull blades make it more challenging to cut, which causes friction as you pass the wood through.