‘Chainsaw kickback’ is a phrase that is used when discussing operating chainsaws. To ensure absolute safety, it is extremely important to ensure you’re well versed in what it means and how to handle it. To fully prepare for chainsaw kickback you first need to understand what it is, how it happens and how to avoid it.
Step 5: If you are using your saw for felling or crosscutting, boring the chainsaw bar into the trunk may be the best way to cut. Step 7: Pay attention to the nose of your chainsaw bar and how it is positioned. Step 9: Use narrow-nose bars, such as Oregon Double Guard bars, to ensure maximum kickback safety.
Kickback is the term to describe the unexpected upward motion of the guide bar. Kickback – the rapid upward motion ofh te guide bar that can occur when the saw chain, near the nose of the top area of the guide bar, contacts an object such as a log or branch, or the backwardm otion that can occur when the wood closes in and pinches hte saw chain in the cut. The most common and probably most violent kickback occurs when contact is made, either accidentally or intentionally, in this “Kickback zone.” In some cases the blade tip may move upward and back toward the operator who could suffer a very serious or fatal injury.
Kickback happens when the chain’s rotational energy gets thrown back at you, and you lose control of the saw. LINEAR KICKBACK. If the chain gets pinched on either side by the wood being cut, the whole saw can get pushed back at you, full speed. PULL-IN KICKBACK. If your saw hits a branch on the other end of the wood, or even a nail, it can yank the saw forward and away from you.
The reason it has this name is that the chainsaw tip is the most common part of the chainsaw that can cause a kickback. If you’re cutting with a chainsaw and the wood closes around the chain tightly, it can cause a chainsaw kickback to occur. Chainsaw kickback is the most common type of chainsaw injury that people encouter.
how to stop chainsaw kickback Related Question:
What causes kickback on chainsaws?
There are two circumstances that can cause kickback when using a chain saw. The first occurs when the moving chain at the tip or the nose of the guide bar strikes an object. The second situation is when the wood closes in, pinching the saw chain in the middle of the cut.
Why does my chainsaw bounce when cutting?
Chainsaw chain jumps and is broken The chain saw belt jumps when it breaks at full speed. This situation can be caused by using an unsuitable chain. This happens when you are cutting very hard wood with a gouge chain. It is indeed very important to choose the right belt for the job to be done.
How often does chainsaw kickback happen?
Kickback can happen in the blink of an eye too. In fact, about 30,000 chainsaw-related injuries happen each year, with chainsaw kickback accidents being the most common hazard.
What is the most common chainsaw injury?
The most common hazards associated with chainsaws are injuries caused by kickback, pushback, and pull-in. Kickback is the most common and poses the greatest hazard. Kickback occurs when the rotating chain is stopped suddenly by contact with a more solid area throwing the saw rapidly backward toward the operator.
What causes a kickback?
The two main causes of injury from kickback is trauma from the wood striking the head, chest, or torso of the woodworker, or the wood moving so quickly that an operator doesn’t have time to take their hand off of it and it gets pulled across the saw blade.
How do I stop my chainsaw from pinching?
To stop your chainsaw from getting stuck, make a cut on top of the log or tree that’s preferably one-third of the log’s diameter. Use your chainsaw to cut from the underside until you meet the initial top cut. Always stand on the side when cross-cutting to prevent injury.
What should you not do with a chainsaw?
Don’t Cut With Improper Blade Tension A overly loose or tight chain also wears out the drive sprocket and causes rapid chain and bar wear. To determine if your chain is properly tensioned, pull up on the chain. The drive links should still be in the bar groove. If the links come out of the bar, the chain is too loose.
Can you drill holes in chainsaw bar?
Re: Drilling a Chainsaw Bar Drilling that bar may not be as difficult as you think. It will be best if you use a drill press, start with a pilot hole, and then drill to the size you need. Make sure you have a sharp bit, run at the lowest speed you can, and use cutting fluid.
What’s the safest chainsaw?
Chainsaws are useful when doing work on your home, but they can feel dangerous to use. It’s not too bad if you know what you’re doing, but it’s so easy to make one wrong move—and then it’s game over. Enter the WORX JawSaw.
Where do you stand to avoid kickbacks?
While standing to the left of the blade is the safest spot, you could still get hit by a kickback. The best way to avoid a kickback is to prevent it. Keep firm control of your material at all time.
Do you need anti-kickback pawls?
It should go without saying that no one safety device can make a saw 100% safe. While anti-kickback pawls will reduce your risk of injury or equipment damage do not neglect to act carefully and to use other safety equipment.
Why does my chainsaw dull so fast?
Dirt Causes A Chainsaw To Dull If you’re cutting through logs and your angle of approach is too steep, a simple cut through could nick dirt or even worse, rocks on the floor causing your chainsaw to jerk, thus dulling.
Should you run a chainsaw at full throttle?
Engine Protection Generally, two-stroke chainsaw engines are built to conveniently run at full throttle without an engine breakdown. Therefore, running at any throttle speed below the full throttle is not advised.
How long does it take to break in a new chainsaw?
Typically we recommend a break in period of 6-10 tanks of fuel. During this period the engine should not be allowed to run at high RPMs for extended periods of time.
Should you break in a new chainsaw?
If you just purchased a new Stihl chainsaw, it’s a good idea to break it in before using it for any cutting projects. Immediately using it to cut anything, particularly very heavy or dense wood, can ruin the chain.