Tightening the screw will tighten the chain, and loosening will loosen the chain. Visit our Chainsaw Chains page to our inventory of available replacement chains and other chainsaw accessories. eReplacementParts.com stocks thousands of parts for many major chainsaw brands, including Echo chainsaw parts.
You must check the chain tension every time you use the chainsaw and make adjustments when necessary. The video below from Echo demonstrates the proper way to adjust a chain tension. Many new cordless chainsaws have a chain adjusting dial instead of a screw, which allows you to adjust the tension by hand.
A damaged bar or chain may cause the chain to come loose from the bar and can be very dangerous when operating the machine. A properly-tensioned chainsaw chain should still be just a little loose on the chainsaw guide bar, but the chain needs to be tight enough that you can’t pull the drive links out of the bar nose. If the bar is near the end of its life and the chain is also worn the side play can also de-rail the chain.
Unlock the chain brake, and install the clutch cover over. IMPORTANT. Always loosen clutch cover nuts before turning the chain. Tension adjuster, otherwise the clutch cover and tensioner.
how to tighten echo chainsaw chain Related Question:
Why does my chainsaw keep throwing the chain?
The drive sprocket is the mechanism that propels the saw blades on the chain around the bar. If the sprocket gets significantly worn down, it will be impossible to maintain proper chain tension, which will result in your chain saw throwing its chain.
Should the chain on a chainsaw be tight or loose?
The chainsaw chain should feel snug but still pull freely. Finally, perform a “snap” test to ensure proper saw chain tension. Simply pull the chain on the underside of the guide bar down so one or two drive links are out of the guide bar rails and release it.
Why does my chain keep getting loose?
Your chain might simply be too old or can stretch over time. When this occurs you need to replace it. Consider that your loose chain also may be due to operator error. Exceeding the recommended gear range for the rear derailleur on your bike may lead to a droopy chain when you ride in these gears.
How do I stop my chainsaw chain from stretching?
Every chainsaw has a tension screw that’s located at or close to the base of the chainsaw bar. If you want to tighten the chain, turn the tension screw clockwise. If you want to loosen up the chain, turn the tension chain counterclockwise.
Why does my chainsaw blade get dull so fast?
Is the wood that you’re cutting with the chainsaw particularly dirty? Many chainsaw enthusiasts have noted that their blades dull faster when they’re cutting muddy wood. If the logs that you’re cutting up are muddy, then perhaps that is the sole reason why your blade is dulling too fast.
Can I use vegetable oil instead of bar oil?
Effective – Vegetable oils have natural properties including good lubricity, resistance to shear, a high flash point, and a high viscosity index. These qualities lend themselves to chain lubricant requirements similar to petroleum-based chain oils, and do not contribute to chain or bar wear over time.
Why does a chain stretch in service?
Another highly significant factor in chain stretch is the accumulation of dirt particles between parts of a chain. These particles form a paste with existing petrochemical lubricants, and they will cause pins, rollers, and bushings to lose material rapidly, again resulting in an overall elongation of the whole chain.
How often should you tighten motorcycle chain?
Too tight is as bad as too loose, but it’ll only take minutes to get it right. You should check and adjust your chain every 500 miles (805 km), and more often for a dirt bike. It’s also a great time to look for kinks or rust, and to give your chain a quick cleaning and lubrication, too.
Can a chainsaw chain stretch too much?
Chainsaw chains stretch during normal operation and begin to sag on a saw’s guide bar. If a chainsaw chain is allowed to become too loose, it can easily come off the bar during operation and create an unsafe situation for the user. Chainsaw chain tension should be checked and tightened often.
How often do you tighten chainsaw chain?
The chain isn’t actually becoming tighter—instead, as you turn the tensioning pin—it pushes the chainsaw bar out a little bit, which takes up the slack on the chain. During a typical afternoon wood-cutting session that lasts 2 to 4 hours, you may need to tighten the chain two or three times.
How often should you replace your chainsaw chain?
The chain sprocket must be replaced if the depth of the wear marks reaches about 0.5mm, i.e. the wear limit. A seriously worn chain sprocket can cause the chainsaw chain and guide bar to wear at an increased rate, as well as reducing cutting performance too, so it’s important to keep an eye on.
Is Echo as good as Stihl?
Conclusion. Echo and Stihl are both options. If you want a powerful and lightweight chainsaw, then an Echo model might be the right choice for you. Stihl makes more sense if you are after a well-built, durable, full of extra features, fuel-efficient chainsaw.
How long should a chainsaw blade stay sharp?
A chainsaw may only need to be sharpened once a year if it is rarely used, but a tool that is frequently used will need to be sharpened regularly to ensure that the blade doesn’t get too dull. On average, a chainsaw blade will retain its sharpness for about 3 hours of actively cutting through wood.
Why does my chainsaw bar smoke?
This most commonly is a result of a dull chain and exerting to much pressure on the bar and chain trying to make the chain saw cut. This could also be either a lack of bar and chain oil ( tank empty, restricted oiler hole ) or an inferior type of oil that is being slung off the chain and not lubricating.
Can I use 10w30 for chainsaw bar oil?
As a matter of fact, you can actually use regular 10w30 motor oil on a chainsaw as one of the alternatives in case you don’t have bar and chain oil. That’s because 10w30 oil has enough thickness and viscosity that will allow it to withstand the friction that is happening whenever you are using a chainsaw.