Chain Tension Chain Sharpening mWARNING! To ensure that the chain saw works safely and efficiently, it is essential that the cutting components are well-sharpened. The saw runs, but the chain speed is low Bar and chain running hot and smoking The saw motor runs, but the chain is not turning If you drop the saw, carefully inspect it for damage. Check the bar and chain oil level; fill with only new chain oil specifically formulated for chain saws.
First, this company has it going!! The product, while inexpensive, is really well designed and produced. Simply type the model number into YOUTUBE and you’ll find the video. Sun Joe, if you’re reading this, a bright card in the box with that info would have given me the desire to give you 6 stars!
First, this company has it going!! The product, while inexpensive, is really well designed and produced. Simply type the model number into YOUTUBE and you’ll find the video. Sun Joe, if you’re reading this, a bright card in the box with that info would have given me the desire to give you 6 stars!
how to tighten sun joe chainsaw Related Question:
Is Sun Joe pole saw a good brand?
Overall, the cuts with the Sun Joe saw are very good (the super sharp chain and automatic bar and chain oiler make sure of that). Despite its rather large cutting head, the saw is able to get into pretty tight places to provide a proper pruning cut.
What kind of oil do you use for Sun Joe chainsaw?
SUN JOE® Saw Joe Bar, Chain Sprocket Oil (model SWJ-OIL) is the cutting edge in high-performance bar and chain oil, reducing friction, prolonging the service life of bars, chains, and sprockets as well as resisting oil thrown off at high chain operating speeds.
Is all chainsaw bar oil the same?
The viscosity of chainsaw bar oil can vary depending on the formula but 30W is standard. In cold weather, a thin 10W chainsaw oil may be advantageous, while very hot temperatures may require a much thicker 40W or 50W formula.
What is oil SAE?
An SAE oil is a motor oil that complies with the SAE standard. What’s that? Motor oils are classified by viscosity, using a rating system developed by the SAE (Society of Automotive Engineers). The letters “SAE” should precede the oil viscosity on the motor oil labeling.
What is chain oil for chainsaw?
Petroleum-based bar oil has been the standard for chainsaws. Lightweight oil is used in winter and heavier oil in summer.
Why is my pole saw not cutting?
The most common cause of a chainsaw that won’t cut properly is a dull cutting chain. Try sharpening or replacing the chain. The chain may not have the proper amount of tension. If the adjustment screw is too loose, the chain may not make good contact with the wood.
Why is my chainsaw chain not tightening?
If you’re having trouble tightening the chainsaw chain, it may be adjusted properly already. Check the tension on the chain by grasping it in the middle of the top of the guide bar and giving it a quick snap. The chain should quickly snap back into place with no sagging on the underside of the guide bar.
Why is my chainsaw chain loose?
Chain Not Set Properly One of the most common reasons why your chain might be coming loose is because it was not set properly. When you go through the steps to tension your chain, you need to finish those steps by setting the tension so it won’t change as you work your saw.
How often should you tighten chainsaw chain?
The chain isn’t actually becoming tighter—instead, as you turn the tensioning pin—it pushes the chainsaw bar out a little bit, which takes up the slack on the chain. During a typical afternoon wood-cutting session that lasts 2 to 4 hours, you may need to tighten the chain two or three times.
Can I use 10w30 for chainsaw bar oil?
As a matter of fact, you can actually use regular 10w30 motor oil on a chainsaw as one of the alternatives in case you don’t have bar and chain oil. That’s because 10w30 oil has enough thickness and viscosity that will allow it to withstand the friction that is happening whenever you are using a chainsaw.
Can I use 2 stroke oil for chainsaw bar oil?
Can You Use 2 Cycle Oil As Bar Oil? You should only use two-cycle oil as the mix, never as a chainsaw bar oil alternative. Using two-cycle oil on the bar will not provide enough tackiness to stick to the chainsaw chain in the summer months. Two-cycle oil also will not work in the winter.
Can you use 10w40 in a chainsaw?
You can but it’s not very good for the chain or the environment. The Husqvarna / Stihl stuff is much thicker and vegetable based so it doesn’t fling off the chain as easily or poison your garden! 10w30. Thicker.
What does the 10 in 10W30 stand for?
Answered January 07 2020. The 10W30 designation on engine oil means that the viscosity of the oil is rated at 10W when an engine is cold and 30 when the engine is hot. This is different than an oil labelled 5W30, which has a thinner viscosity when the engine is cold at 5W.
Is it advisable to put more oil to the engine?
Engine damage – Too much lubricant in the system can cause pressure on the crankshaft to increase. This can result in oil entering the crankshaft exhaust pipe, running through into the combustion chamber, blocking the suction hose with oil soot and potentially leading to engine overload.
What does 15W40 mean?
15W40 refers to the SAE class according to which the engine oil was classified. The SAE class describes the viscosity of an oil, i.e. its flow properties as a function of the operating temperature. Engine oils of class 15W40 are multigrade oils. These have good flow properties at cold and warm temperatures.