A catalyst for this seems to be Jim Cummings article “Home Shop Bandsaw” in Fine Woodworking #63. From the hundreds of bandsaw owners I’ve talked with since the article appeared, it seems there are lingering questions on how to adjust a bandsaw blade, the blade choice and operation. “To find the correct tension, you can start with the tension scale on your saw, but you will probably need to fine tune the adjustment. With the saw unplugged, increase the tension on the blade until pushing on the side of the blade with your finger using a moderate amount of force deflects the blade about a 1/4” from its normal position. An interesting experiment is to set the side guys too far from the blade and notice how increased feed pressure and turning make the blade wander.
A long straightedge should touch the tops and bottoms of both wheels simultaneously in order for the blade to track on the center of both wheels, photo below left. Reinstall the blade on the center of the tires and add tension while slowly turning the top wheel by hand. Hand-spin the wheels to check blade tracking and make any final adjustments before giving the blade a short test with the motor running.
Install the blade and apply just enough tension to keep the blade securely on the wheels. Instead, tension the blade until your finger is only able to deflect the blade by about 1/4″. This test should be done at the back of the saw where nothing can get in the way of the blade. Adjust the thrust bearings carefully so that they do NOT rotate while the blade moves, but they DO begin to rotate as soon as light pressure is applied to the blade.
how to tune a bandsaw blade Related Question:
How much play should a bandsaw blade have?
Bandsaw blades require tension and lots of it to consistently produce straight, uniform cuts, especially in thick or dense stock. Most blade manufacturers recommend 15,000 psi to 20,000 psi for a common carbon-steel blade.
Why won’t my bandsaw cut straight?
Band Saw: Why won’t my band saw cut straight? When the band saw cuts crooked, a dull blade, improper feeding, loose blade tension or not using a work piece guide could be the cause. Use the rip fence or miter gauge to guide the work piece uniformly through the cutting blade to make straight cuts.
Why is my horizontal band saw not cutting straight?
Make sure the blade is running in the correct direction. On machines powered by three phases power so it is common to get the wiring reversed and have the blade running the wrong direction. On all vertical blade bandsaws the working portion of the blade should go down. This forces the workpiece down into the table.
How tight should a sawmill blade be?
For carbon steel toothed blades (cutting blades) this is typically 15,000 to 25,000 PSI. Slitting type blades typically are tensioned in the range of 12,000 to 20,000 PSI. In general bandsaw blades are never tensioned past 35,000 psi.
How long should a bandsaw blade last?
On average your bandsaw blade should last 6 months to as long as a few years depending on what your cutting with it. Make sure to match your blade strength and quality to the project and material your cutting.
Why do bandsaw blades break?
Machine Defects Even the best blades can fail if there is something else wrong with your bandsaw, and even a small misalignment of bearings or guides can put a twist in the blade as it goes around. Resulting in tension being applied in all the wrong ways which will lead to early breakage.
What is Resawing on a bandsaw?
Bandsaw Resawing from the beginning: resawing is cutting a sawn plank of wood into thinner planks on a bandsaw. Thus the cut runs through the plank’s width, which distinguishes bandsaw resawing from ordinary bandsaw rip cuts where the blade runs through the stock’s thickness.
Why does my bandsaw spark?
Ceramics can cause sparks. Or, if your thrust bearing is too far past the blade, more toward the center of the bearing than the edge, then it won’t turn and you’ll get sparks too, and possibly wear a groove in the bearing.
Why does my bandsaw blade wobble?
The blade on a saw left idle for long periods of time can leave an impression in the rubber tire which might cause erratic tracking. Purchase and install aftermarket replacement tires. (Search for “bandsaw tire” at woodcraft.com.) If you still see a back-and-forth motion, the culprit is probably the wheel itself.
Why are my bandsaw cuts wavy?
Re: Band saw Cutting Wavy Cuts. The clasic cause for wavy lumber is pushing a dull blade past it’s limits. Sharp don’t get it. On these low powered mills, the blade gotta be razor sharp..
Which way should the teeth face on a bandsaw?
The teeth on the bandsaw blade should face down so that the cutting action is from the top of the material to the bottom.
Why do bandsaws wander?
Tim Inman: Because band saw blades ride on crowned wheels, they always have a little “camber” angle relative to the vertical axis of the wheel. This causes the blade to tip a little and makes the cut “pull” to the side.