Follow these steps to start and stop a Husqvarna chainsaw to ensure safe usage and a longer life for your chainsaw. Activate the chain brake before starting the chainsaw. When starting you chainsaw with a warm or previously run engine, pull the choke control out and push it back in again.
Flooded engines can be started by placing the choke lever in the OFF CHOKE position; then, pull the rope to clear the engine…. Check to ensure that there is fresh, clean fuel in the fuel tank. Also check the fuel filter, because a clogged fuel filter will prevent the engine from obtaining adequate fuel supply. Damaged fuel line or fuel filter…. Drain all the fuel and bar oil out of the chainsaw.
how to turn off husqvarna chainsaw Related Question:
How do you stop a chainsaw?
To stop your chainsaw from getting stuck, make a cut on top of the log or tree that’s preferably one-third of the log’s diameter. Use your chainsaw to cut from the underside until you meet the initial top cut. Always stand on the side when cross-cutting to prevent injury.
What is the button on top of a Husqvarna chainsaw?
What is a decompression valve? A decompression valve releases some of the compression from the combustion chamber during the starting procedure, making the engine easier to turn over when pulling the recoil rope.
Do you start a chainsaw with the brake on or off?
Check the Chain Brake When engaged, the chain brake stops the chain from rotating around the saw’s guide bar. When using a chainsaw, you should always start it with the chain brake engaged so the chain does not move.
How do you get a chainsaw unstuck from a tree?
The best way to free a trapped chainsaw is to use a felling wedge or a crowbar to gently lift the pressure and tension of the tree off of your chain and bar. Before attempting to do this the engine should be turned off to prevent the chain from accidentally moving and causing damage or injury.
Why will my Husqvarna chainsaw not start?
The carburetor might be clogged. A clogged carburetor is often caused by leaving fuel in the chainsaw for a long period of time. Over time, some of the ingredients in the fuel will evaporate, leaving behind a thicker, stickier substance. This sticky fuel can clog up the carburetor and prevent the engine from starting.
When should I use choke on my chainsaw?
The choke position is the fourth setting on the master control lever. This setting is used to start the saw when its motor is cold. Stihl chainsaws denote the choke position using a nearly horizontal squiggle between two vertical lines at the lowest position on the master control lever.
What is the T adjustment on a Husqvarna chainsaw?
The T screw regulates how much fuel is sent to the carburettor while idling until the throttle is pressed. L Screw – With the chainsaw still running, take a screwdriver and turn the L screw clockwise. Keep turning it until the engine almost stops turning.
Why does my Husqvarna chainsaw stall?
A clogged carburetor is often caused by leaving fuel in the chainsaw for a long period of time. Over time, some of the ingredients in the fuel may evaporate, leaving behind a thicker, stickier substance. This sticky fuel can clog up the carburetor and cause the chainsaw engine to stall.
Can you cut with the top of a chainsaw?
While it’s designed to cut with either the top or bottom of the blade, just about anything that comes in contact with the top half of the end tip of the blade (known as the kickback zone) can change the cutting momentum and cause the saw to slam back against you.
Why is my chainsaw kicking back?
There are two circumstances that can cause kickback when using a chain saw. The first occurs when the moving chain at the tip or the nose of the guide bar strikes an object. The second situation is when the wood closes in, pinching the saw chain in the middle of the cut.
Why is my chainsaw hard to pull and kicks back?
If your chainsaw is hard to pull, here are some common causes: The pully system is snagged or stuck. The starter assembly is stuck or sticky. The housing may be damaged.
What are metal bucking spikes on a chainsaw?
Bumper Spikes: This series of sharp metal spikes protruding from the saw near the base of the bar provide leverage for easier, more controlled sawing. Jab the spikes into the log, then pivot the bar downward to guide the chain through the cut.
Are Husqvarna chainsaws hard to start?
While most Husqvarna chainsaws start up even years after they’re first purchased, with minimal effort, a few may have difficulty even from the beginning.
Why does my chainsaw stall when I give it gas?
If the filter becomes clogged, not enough fuel will reach the engine for it to run properly. Because your chainsaw will idle, but dies when it is revved up to full power, it means that the filter is only partially clogged; it will allow enough fuel to the engine to run on idle, but not enough to sustain full throttle.
What is the choke on symbol?
The choke on symbol for most small engines looks like a horizontal ( — ) or diagonal ( / ) line. It also can simply say ‘Choke’, ‘Full Choke’, or ‘Start’. The off symbol for most small engine chokes is represented by a vertical line ( | ) or the word ‘Run’. Hopefully you have learned something here.