Starting a flooded chainsaw – A quick guide One of my youngest memories is being with my father in an orchard somewhere cutting trees for firewood. Let your chainsaw sit for 15-20 minutes to allow the fuel to evaporate from the engine and then repeat the starting instructions. Employe short, brisk pulls instead. If the engine does not start in 15 pulls then the spark plug may be ‘wet fouled’.
If you need to learn how to start a flooded chainsaw, don’t worry, you’re not alone. For starters let’s look at how the engine became flooded to begin with, and then I’ll show you a couple of really easy ways to get your chainsaw up and running again. The second option is my favorite way to start a flooded chainsaw and I believe it’s the easiest and most effective way.
Stihl chain saws have a choke that makes cold starting easier, but you have to use it properly. If the engine doesn’t start on the first three or four pulls, the fuel and air mixture becomes fuel rich, and if you continue to pull the starter while the choke is closed, there is too much fuel to ignite and the engine floods. You can simply wait for the fuel to drain, but there is a faster way to clear the engine.
Does your chainsaw not start? Could be multiple causes that prevent for your chainsaw from starting, but don’t worry because I will show you exactly how to fix your chainsaw! In this article I will show step by step how to start a chainsaw no matter the problem! How to determine if a chainsaw is flooded?If you suspect a flooded chainsaw spark plug, you must inspect it. How to prevent a chainsaw from floodingPreventing a chainsaw from flooding may not be a feasible task. Step 1: Remove the gas and oil from chainsaw when storingIf your chainsaw is used for casual or seasonal use, you should drain all the fluid from it before storing. Step 4: Do not force the chainsaw to startSometimes making a cold start on any two-stroke chainsaw engine requires a few tries until it is started successfully. The spark plug is the main component of the ignition, respectively, of the start of the operation of the entire mechanism of any of the gasoline-powered tools knowing how to start a flooded chainsaw will be useful to both a beginner and an experienced user.
how to unflood chainsaw engine Related Question:
Can you over prime a chainsaw?
If the engine will not start, the most likely failure is that your chainsaw has flooded due to over-priming of fuel or the choke has been left too open, causing too much fuel to enter the combustion chamber.
How long does it take a flooded chainsaw to start?
Steps to Start a Flooded Chainsaw: It only takes five to ten minutes to start a flooded chainsaw. You need to pull the rope to start the chainsaw. If it fails to start, check the spark plug and replace the air filter.
How do you start a hard start on a chainsaw?
Try to start the chainsaw after priming the carburetor. 5. Activate the choke by moving the lever to the full choke position and pull the starter rope 3 or 4 times to start the engine. If that doesn’t work, move the choke lever to half choke and pull the starter rope, 6 times maximum, to start the engine.
How do you know if a 2 stroke is flooded?
If you cannot get the engine to sputter, the easiest way to diagnose flooding is to check the spark plug. If the spark plug is coated in gas, the engine is flooded. Removing the spark plug and drying it thoroughly is recommended (source).
Will a flooded engine fix itself?
Will a flooded engine fix itself? No. You have to take appropriate measures to restore the fuel and air balance in your car’s engine.
How long to wait if engine is flooded?
Perhaps the best remedy for a flooded engine is time. Simply open the hood of your car and let excessive fuel evaporate for as long as you can. After about 20 minutes try starting your car again without hitting the gas pedal.
Why can’t I start my Stihl chainsaw?
Dirty or clogged fuel tanks, dirty fuel filters and lines, loose fuel hoses, dirty air filters and a dirty carburetor can all restrict fuel flow. Check, clean and replace all the fuel system parts before moving into the internal engine, as gas problems create a majority of starting problems.
Why won’t my chainsaw start when it’s hot?
When your chainsaw quits after it gets hot, you either have a problem with gas flow being restricted into the engine or with the spark. This is a common occurrence on older-model chainsaws. By replacing your spark plugs and keeping your gas lines clear you can reduce the chances of this problem recurring.
What causes a 2 stroke engine to flood?
The engine may flood because of overpriming or because the choke has been left open too far, causing an excess amount of fuel to reach the combustion chamber. If your two-stroke engine is flooded, you can get it started with relative ease.
Can you flood a two-stroke engine?
Overpriming or a choke that has been left open too far may cause the engine to flood, resulting in an excess amount of fuel entering the combustion chamber through the choke. You can start your two-stroke engine relatively easily if it is flooded.