If blade is pinched bring saw to a complete stop and back out of the cut. Cut only as fast as the blade can properly remove material. Use a push stick for cut that would bring your hands close to blade.
Make sure you understand the instructions before attempting to use any tool or machine. Securely anchor the band saw to the floor to reduce vibration. Refer to Woodworking Machines – General Safety Tips for general safety precautions.
Adjust the upper blade guard so the blade is completely covered. Use the correct width blade for the desired cut radius. Never push stock directly into the blade with your hand in line with the cut without a push stick.
Marvel Vertical Band Saw Safety Rules Do not push the blade into the workpiece hard enough to cause the machine to chatter; slow down and find a more rigid manner in which to clamp the work in the saw. The proper procedure is as follows: firmly clamp the workpiece in the vice; turn on the saw so the blade is rotating; adjust the coolant if necessary; gently bring the moveable saw blade into light contact with the workpiece by rotating the manual feed wheel; engage the automatic feed. Table Saw Safety Rules Special training is required before using the table saw.
how to use a band saw safety Related Question:
What is the most important rule to remember when using the band saw?
Stand to one side, never directly in line with, of work being fed through the saw. Use the proper blade for the material and type of cut. Do not use a rip blade for cross cutting, or, a crosscut blade for rip sawing. Do not use a plywood blade for anything but plywood.
What are three 3 safety rules to follow when using the bandsaw?
Safety Rules Safety glasses are required. Never clear small pieces while blade is moving. Never adjust saw or setup while saw is running. Never cross arms.
Should you wear gloves when using a bandsaw?
Do not wear gloves while using a bandsaw (or any powered saw, drill press, or planer for that matter). The gloves will give you a false sense of security and do very little to protect your hands. In fact, they may end up getting your fingers pulled into the blade if the material catches.
How far should the safety guard be above the stock?
Keep guards in place at all times. The blade guard should be from 1/8 to ¼ inch above stock. Keep hands away from blade and do not open upper or lower bandsaw doors while blade is in motion.
How does a band saw work?
Band saws use blades that are in a continuous loop around the saw’s wheels. With band saws, the blade cutting direction is always downward. This feature allows the band saw to handle more substantial work, like cutting down large pieces of lumber.
What must you never do when using the bandsaw to ensure you don’t pull off the blade?
Make curved cuts gradually and use relief cuts for tight radius curves. Never back out of curved cuts while machine is still running as this will result in the blade coming off. (You must wait until blade comes to a complete stop).
When you are finished using the band saw you should?
If it becomes necessary to back out of a long cut, you should: Turn off the motor. Bring the blade to a complete stop and then back the stock out carefully. Force the wood into the blade to get a good cut.
How far should fingers be kept away from the blade of a band saw?
1. Set the saw guide to within 1/2 inch of the stock before turning on the power. 2. Do not put your fingers closer than two inches from the blade.
Can a bandsaw cut your finger off?
it cuts pinky fingers really well. all the way through the bone only skin holding it on. so after notifying the woodshop teacher that a bandaid would NOT work for this one, i ended up on a strecther on the way to the hospital.
What is a Kevlar glove?
Kevlar gloves are a type of personal protective equipment (PPE) made of Kevlar, a strong synthetic fiber used to protect workers from cuts, abrasions and heat. The gloves are also lightweight, flexible and comfortable.
Should you wear gloves around powered rotating equipment?
According to OSHA, those who work around rotating or otherwise moving equipment should not wear gloves, as they can make things more dangerous for the worker by getting caught on the machine and pulling them into it.
What should never be in line with the blade?
The leading hand should never be closer than is necessary to the front of the saw and hands should never be in line with the saw blade. A push-stick should always be used to remove the cut piece from between the saw blade and fence, unless the width of the cut piece exceeds 150 mm.
Where should your fingers stay while cutting with the band saw and scroll saw?
Keep your fingers to the side of the saw blade. Never allow your fingers to be in front of the saw blade. Your fingers must be positioned more than two inches from the blade when the saw is operating. When cutting cylindrical (round) stock, secure stock in a “V” fixture.