Tomorrow, because proper maintenance is a key to optimum, injury-free use, we’ll cover how to keep your saw in tip-top condition. There are two methods to safely start a chain saw: on the ground and, yes, between your legs. “Pinching the bar” is a good segue into the directional pressures present in the limb, log, or standing tree that dictate how the saw operator will approach the cut.
Kickback happens when the chain’s rotational energy gets thrown back at you, and you lose control of the saw. LINEAR KICKBACK. If the chain gets pinched on either side by the wood being cut, the whole saw can get pushed back at you, full speed. PULL-IN KICKBACK. If your saw hits a branch on the other end of the wood, or even a nail, it can yank the saw forward and away from you.
Before you go firing that bad boy up and hacking away at everything in sight, there are a few rules you need to follow for how to use a chainsaw safely. If you don’t own a chainsaw yet, and you’re reading this guide just to get a good idea of how to operate one before you buy it, I invite you to check out my top battery chainsaw reviews. As a reminder, if you’re in the market for a new chainsaw, don’t forget to check out my top battery chainsaw reviews, top chainsaws list, and the best chainsaws for firewood.
Do it the right way and prevent chainsaw injuries and chainsaw cuts. Cut with the top or bottom of the bar and chain, but avoid the kickback zone Kickback zone on a chainsaw. Chainsaw Cuts: Cutting the Tree Trunk Photo 4: Start cutting downward in the trunk.
how to use chainsaw properly Related Question:
What should you not do with a chainsaw?
Don’t Cut With Improper Blade Tension A overly loose or tight chain also wears out the drive sprocket and causes rapid chain and bar wear. To determine if your chain is properly tensioned, pull up on the chain. The drive links should still be in the bar groove. If the links come out of the bar, the chain is too loose.
Do you cut up or down with a chainsaw?
Never cut above shoulder height. Work on the uphill side of trees so they’ll roll away from you instead of over you. Use your chain brake! Whenever you aren’t cutting, the brake should be in the locked, or “On,” position.
Should you run a chainsaw at full throttle?
Engine Protection Generally, two-stroke chainsaw engines are built to conveniently run at full throttle without an engine breakdown. Therefore, running at any throttle speed below the full throttle is not advised.
Can you cut wet wood with a chainsaw?
Can you cut wet wood with a chainsaw? Yes, you can cut the wet wood with a chainsaw. Besides, there is a misconception that wet wood can impact the chainsaw bar and chain. But actually, the damp wood will not dull the chainsaw any faster than using it on other types of wood.
What is the most common chainsaw injury?
The most common hazards associated with chainsaws are injuries caused by kickback, pushback, and pull-in. Kickback is the most common and poses the greatest hazard. Kickback occurs when the rotating chain is stopped suddenly by contact with a more solid area throwing the saw rapidly backward toward the operator.
What causes a chainsaw to kick back?
Kickback is the term to describe the unexpected upward motion of the guide bar. Kickback occurs when the end portion of the nose of the bar (the kickback zone) strikes an object and the chain momentarily snags, or is pinched.
What size chainsaw do I need to cut firewood?
Many homeowners find that a 14- to 16-inch chainsaw is a good length for them. That’s long enough to limb-up trees, cut down small trees, and cut most firewood, but it’s also short enough that it’s easy to control the saw.
What should you not do when a tree falls off?
When cutting up a felled tree, avoid touching the ground with the chain because even a brief encounter will severely dull the cutting teeth on your chain saw. If possible, cut partially through the tree and then rotate it to cut the rest of the way through.
How long does it take to cut down a tree with a chainsaw?
Some trees can be taken down in as little as 15 minutes, while others can take a few hours. Usually, the more cramped or crowded the location of the tree, the longer it will take to remove. Your professional removal team will be able to give you a ballpark time estimate once they get a look at the removal site.
How long should you run a chainsaw?
Depending on the type and usage, you can expect a gas Chainsaw to run between 15 and 40 min before you have to fill it up again. Most battery-powered chainsaws have a run time of up to 2 hours, but there are high-capacity power packs that will last much longer.
How often should you change your chainsaw chain?
The chain sprocket must be replaced if the depth of the wear marks reaches about 0.5mm, i.e. the wear limit. A seriously worn chain sprocket can cause the chainsaw chain and guide bar to wear at an increased rate, as well as reducing cutting performance too, so it’s important to keep an eye on.
Why does my chainsaw bar smoke?
This most commonly is a result of a dull chain and exerting to much pressure on the bar and chain trying to make the chain saw cut. This could also be either a lack of bar and chain oil ( tank empty, restricted oiler hole ) or an inferior type of oil that is being slung off the chain and not lubricating.
Is dry wood harder to cut?
Dry Wood Is Typically Easier to Split Regardless of the tree species from which it was harvested, dry wood contains less moisture, so there’s less resistance when cutting and splitting it. An ax or log splitter blade will easily cut through dry wood thanks to its low moisture content.
Can you drill holes in chainsaw bar?
Re: Drilling a Chainsaw Bar Drilling that bar may not be as difficult as you think. It will be best if you use a drill press, start with a pilot hole, and then drill to the size you need. Make sure you have a sharp bit, run at the lowest speed you can, and use cutting fluid.
Should you flip your chainsaw bar?
Every chainsaw bar has been designed to be mounted right-side up or upside down. The reason for this is that it allows the user to extend the life of his chainsaw bar by 50%. Flipping the bar will give the heavily-used areas some relief from wear and tear.