how to use petrol chainsaw Related Question:
How does a petrol chainsaw work?
It has an air-cooled two-stroke gasoline engine. The chain is driven by a centrifugal clutch. When the engine is idling, the clutch is disengaged. When the engine speeds up, the centrifugal plates in the clutch spin outward to engage the clutch, and the chain begins running.
What should you not do with a chainsaw?
Don’t Cut With Improper Blade Tension A overly loose or tight chain also wears out the drive sprocket and causes rapid chain and bar wear. To determine if your chain is properly tensioned, pull up on the chain. The drive links should still be in the bar groove. If the links come out of the bar, the chain is too loose.
Is a chainsaw a 2 stroke?
Chainsaw engines come as either 2-stroke or 4-stroke versions. Sometimes these are also referred to as 2-cycle and 4-cycle engines – it’s the same thing.
Are chainsaws easy to use?
If you need to do regular maintenance in your backyard, perhaps removing branches here and there or cutting down small trees, then a small gas-powered chainsaw with a 16-to-18-inch bar is an irreplaceable tool. Due to the small weight and size of the chainsaws in that class, they are really easy to use.
How do you cut a chainsaw?
A chainsaw is a portable saw that cuts through wood or wooden objects by the use of “teeth” running in a circular motion around a guiding bar. The “teeth” on the blade of a chainsaw is actually a metal chain that has notches or grooves at certain intervals to cut through even the hardest types of wood with ease.
How much oil do I add to 5 Litres of petrol?
This is 125mls of two stroke oil to 5L of fuel.
Do you mix oil with gas for chainsaw?
Most STIHL gasoline-powered equipment runs on a 50:1 mixture of gasoline and 2-cycle engine oil. Knowing the proper way to mix your fuel is the first step in keeping it running strong and long.
What is the most common chainsaw injury?
The most common hazards associated with chainsaws are injuries caused by kickback, pushback, and pull-in. Kickback is the most common and poses the greatest hazard. Kickback occurs when the rotating chain is stopped suddenly by contact with a more solid area throwing the saw rapidly backward toward the operator.
What happens if you run a chainsaw without bar oil?
Without lubricant, the speed at which the chain moves over the chainsaw bar can cause some serious friction. A slowed-down chain and excessive fuel burning mean there’s a lot of friction between your bar and chain, which means a lot of heat is being produced that could do major damage to your saw.
Should you run a chainsaw at full throttle?
Engine Protection Generally, two-stroke chainsaw engines are built to conveniently run at full throttle without an engine breakdown. Therefore, running at any throttle speed below the full throttle is not advised.
Can you cut wet wood with a chainsaw?
Can you cut wet wood with a chainsaw? Yes, you can cut the wet wood with a chainsaw. Besides, there is a misconception that wet wood can impact the chainsaw bar and chain. But actually, the damp wood will not dull the chainsaw any faster than using it on other types of wood.
What size chainsaw do I need to cut firewood?
Many homeowners find that a 14- to 16-inch chainsaw is a good length for them. That’s long enough to limb-up trees, cut down small trees, and cut most firewood, but it’s also short enough that it’s easy to control the saw.
How common are chainsaw injuries?
According to the Centers for Disease Control and Prevention (CDC), approximately 36,000 people are injured by chainsaws annually. Medical costs for chainsaw injuries based on these facts amount to about 350 million dollars per year.
What oil do I mix with chainsaw?
Many gas-powered chainsaws run on a 40:1 mixture of gasoline and 2-cycle engine oil. Other chainsaws run on a 50:1 mixture of gas and 2-cycle engine oil. Some older models use a 30:1 ratio. Check your chainsaw’s manual to be sure.
What oil do I mix with petrol for a chainsaw?
Most manufacturers recommend a 50:1 chainsaw oil mix ratio, but some call for 40:1 and even 32:1 in older saws. Most 2-stroke chainsaws recommend a 50:1 chainsaw oil mix ratio.