Chainsaw bar oil is a necessary component to operating your chainsaw at peak efficiency and with safety in mind. Formula Chainsaw bar oils are either petroleum-based or bio-based. ‘ Chainsaw bar oil for winter is usually 10W. Very hot temperatures may call for a thicker chainsaw oil, in the 40W to 50W range.
2) Husky oil, a little cheeper then Stihl oil, but a good run, seems a little warmer running bar, and seem to drip off just a little ‘blacker’ then the stihl oil. Husky oil dode not seem as consistant as Stihl oil to me, but a good run. 3) Power Blend oil, a lot cheeper then Stihl oil, but a noticably warmer running bar, you just get the feeling that it is not as good.
Unless you have a stockpile of gear oil available if your chainsaw oil runs out, it’s not a sound economic decision to buy gear oil as a backup. We recommend turning to canola oil as the best chainsaw bar oil substitute on our list. Chainsaw bar oil substitutes that derive from vegetables like canola oil are the best for your chainsaw.
One of the most common points of confusion for new chainsaw users, is the difference between engine oil, and bar and chain oil. Bar and chain oil is a lubricant used to reduce friction caused by the metal-on-metal contact between a chainsaw’s bar and chain. There’s folks out there, that say regular old engine oil works great as a bar and chain oil.
Knowing the available chainsaw oil options, learning how to choose the right one and determining the right fuel/oil ratio can help ensure your chainsaw runs smoothly every time. Common Issues if Chainsaw Oil Is Bad. Chainsaw engine oil can go bad. Two-cycle oil is good for up to five years when sealed, and many manufacturers list the oil’s shelf life on the container. “One thing we do for our customers who buy a chainsaw that requires an oil/gas mix is we have them buy a gas can and we write the formula right on the can with a big black Sharpie. Then, the next time they need to make the mixture, they can dump in the right amount of oil and take the can to the gas station and pump in the right amount of gas.”
is all chainsaw bar oil the same Related Question:
Can I use any oil for chainsaw bar?
Generally, chainsaws can handle a wide range of lubricants. Vegetable and canola oils work well, and automobile motor oil will too, as long as you observe the SAE ratings and use the appropriate oil weight for the season. Always use fresh, never used, oils.
Does chainsaw bar oil matter?
Petroleum-based bar oil has been the standard for chainsaws. Lightweight oil is used in winter and heavier oil in summer. Manufacturers of chainsaws make bar and chain oils specially blended for their machines to extend their lifespan, but if they are not available, the owner’s manual suggests alternatives.
What kind of oil do you use for bar and chain on a chainsaw?
If your manufacturer’s bar and chain oil is unavailable, you can use SAE 30 weight motor oil to lube your chain during the summer and SAE 10 weight during the winter, according to the University of Missouri Extension.
Can I use a Husqvarna chain oil on a Stihl?
Can I Use A Husqvarna Chain Oil On A Stihl? The Husqvarna premium bar and chain oil is made of high quality materials: Totally suitable for use with all brands of gas-powered Stihls and electric Makita chainsaws.
Can I use 10w30 for chainsaw bar oil?
As a matter of fact, you can actually use regular 10w30 motor oil on a chainsaw as one of the alternatives in case you don’t have bar and chain oil. That’s because 10w30 oil has enough thickness and viscosity that will allow it to withstand the friction that is happening whenever you are using a chainsaw.
Can you use transmission fluid for chainsaw bar oil?
On occasion I’ve used tranny fluid to clean out old oil residue in old chainsaws . It works well . In addition to that tranny fluid seems to pump better on some saws with whimpy oilers in cold weather .
What weight is chainsaw bar oil?
What viscosity is chainsaw bar oil? The viscosity of chainsaw bar oil can vary depending on the formula but 30W is standard. In cold weather, a thin 10W chainsaw oil may be advantageous, while very hot temperatures may require a much thicker 40W or 50W formula.
What does 10W30 mean?
The 10W30 designation on engine oil means that the viscosity of the oil is rated at 10W when an engine is cold, and 30 when the engine is hot. This is different than an oil labelled 5W30, which has a thinner viscosity when the engine is cold at 5W.
Can you use 10w40 in a chainsaw?
You can but it’s not very good for the chain or the environment. The Husqvarna / Stihl stuff is much thicker and vegetable based so it doesn’t fling off the chain as easily or poison your garden! 10w30. Thicker.
Is it OK to use engine oil as bar oil?
While motor oil is not the best substitute for chainsaw bar oil, it will work as a temporary measure if find you have no other option. The downside of motor oil is that it’s not sticky enough to stay on the bar and chain. So, when you’re using the chainsaw, the motor oil will fling off as you cut and make quite a mess.
Can I use 20w50 for chainsaw bar?
you can use new 20w50 mixed with thick used oil (gear box oil or thick truck oil), or SAE 30 & up (You´ll need to adjust the pump debit screw UP!) As for point 2. (few do the pre-start pumping!) use an hidrophobic grease like Retinax A or any other you can get your hands on.
Can I use any 2 stroke oil in my chainsaw?
Can I use any 2 stroke oil in my chainsaw? No, you can’t use any 2-stroke oil in your chainsaw. Some 2-stroke oils are built for motor oils, and this might damage your chainsaw. Also, 2-stroke oils for an air-cooled engine are different from a water-cooled engine.
Is Stihl bar and chain oil any good?
Stihl Platinum Bar and Saw Chain Lubricant It coats all of the blade’s moving parts and keeps everything running smoothly for a long time. It also doesn’t break down very easily in the heat, so it’s effective for a good long while. It has a significant drawback, however, and that is its price.
Can you lube transmission oil as chain?
It’s perfectly fine to use gear oil for lubing motorcycle’s chain, I’m myself using it for years. Use 90 grade gear oil if you lube every 500–700km while the thicker 140 grade oil lasts for 800–1000 km. Also, there’s no need to clean the chain every 500km. Clean the chain when it’s visibly dirty & mucky.
Can power steering fluid be used as bar?
The power steering and gear fluid for your car would work just fine for your saw chain and lube. Synthetic oil, such as power steering fluid and gear oil are great chain lubricant. These are lightweight oil, that can prevent chain brake and bar jamming.