craftsman 2 x 42 belt sander Related Question:
What size belt does a Craftsman belt sander take?
Attach Craftsman’s 4 x 36-in. Sanding Belt, 50-Grit to your belt sander to produce a smooth and professional-looking surface on wood, metal, plastic, fiberglass and more.
Why does my Craftsman belt sander keep breaking belts?
Heat, humidity, and age can contribute to belt seam failures, but they’re not the only causes. Check that your belts are turning in the direction indicated on the inside face. When not using your sander, release the tension on the belt.
What is the most common belt size for a belt sander?
Hand Powered Belt Sander The most common sized belts used on Hand Sanders are 3” x 21”, 3” x 18” and 4” x 24″ sanding belts.
Does craftsman make a cordless belt sander?
CRAFTSMAN V20 20-Volt Cordless Random Orbital Sander with Dust Management.
Can sanding belts be repaired?
You can also mend or make abrasive belts by this DIY method: Obtain some bias binding tape from a fabric store, or you can make your own. Then use CA adhesive to bind the bias binding tape to the cleaned edges of the sanding belt you want to make or repair. I have done this many times, and it works fine.
How much wood can a belt sander remove?
As mentioned earlier, abrasive belts can only remove a certain amount of stock dependent on grit size. With a three-head sander you can run a grit sequence of 100-150-180 and remove approximately 1/32 inch in one pass.
What is the best speed for a belt sander?
The optimal speed for belt grinders is largely dependent on a number of factors, including type of abrasive grain, grit grade, workpiece material, and more. Generally speaking, a safe speed in most cases is 3,000 surface feet per minute. You can calculate surface feet per minute using the formula SFPM = RPM X .
What is better belt sander or orbital sander?
A belt sander is more effective for large materials, while the orbital sander is ideal for small spaces and pieces of furniture. A belt sander works effectively on flat surfaces, while an orbital sander can work with various angles.
How tight should a sanding belt be?
Most wood sanding applications require a belt tension near 40 psi. Because the goal is to keep the belt from slipping, users sometimes err on the side of using too much belt tension. Several problems can result from excessive belt tension.
What kind of sanding belts are best for metal?
As high-performance belts, both zirconia and ceramic sanding belts will last longer and remove metal faster than aluminum oxide or silicon carbide sanding belts. Both belts have the ability to resharpen as they wear and both are primarily used on metal applications. In the end, both types of belts are excellent belts.
Is Craftsman belt sander variable speed?
The Craftsman belt sander has a variable speed design to help you better control your accuracy and allows you to sand many types of materials.
How many amps is a belt sander?
Most of the handheld belt sanders have a 6 or 12 amp motor that is sufficient for most sanding projects. However, if you have to work with larger wood pieces, you will need something with more power.
What type of glue is used to make sanding belts?
Lay one end of the belt, grit-side down, on the bench; then apply cyanoacrylate glue to the end of the belt. Lay half of the bias tape’s width on the glue, place waxed paper over the tape, and use a weight to press down on it for about 30 seconds, or until the glue sets.
What tape is used to join sanding belts?
Apply the Scotch 8959 tape by using a small piece of swimming pool noodle or other firm foam/rubber like a squeegee pressing firmly and leaving overlap on both ends, make sure there are no air bubbles and the tape is perfectly flat covering both splice ends equally.
Can you cut sanding belts?
You can cut sanding strips from sanding rolls or sanding belts. Cutting from sanding rolls is the more ideal solution.