Makita’s 4″ x 24″ Belt Sander, model 9403, combines power and speed with ease-of-use features and less noise for fast and efficient stock removal. “The 9403 features a powerful 11 AMP motor with electronic speed control to maintain constant speed under load, with a 4” wide belt and a speed of 1,640 ft. Variable speed dial : No. Dust bag included : Yes.
Power All stationary belt sanders run off AC current, but you’ll find both corded and cordless portable belt sanders, though corded is the most common type. Cordless belt sanders typically use 18-volt lithium-ion batteries, although some hardier models use 20-volt batteries instead. Most handheld belt sanders’ motors run between 6 and 12 amps of power; if you only need the tool for lightweight and occasional sanding jobs, the lower end of that range is sufficient, but if you plan on tackling larger projects, you’ll be happier with a belt sander that runs towards the top of that range. Speed The speed at which a belt sander rotates the sanding belt is usually measured in feet per minute, although some manufacturers stick with rotations per minute.
belt sander quit working Related Question:
Can belt sander belts be repaired?
You can also mend or make abrasive belts by this DIY method: Obtain some bias binding tape from a fabric store, or you can make your own. Then use CA adhesive to bind the bias binding tape to the cleaned edges of the sanding belt you want to make or repair. I have done this many times, and it works fine.
Why does my belt sander keep breaking belts?
Heat, humidity, and age can contribute to belt seam failures, but they’re not the only causes. Check that your belts are turning in the direction indicated on the inside face. When not using your sander, release the tension on the belt.
When using a belt sander you should never?
1. Do Not use the belt & disc sander if you are too tired, hungry, sad, mad, or dehydrated. Never work while under the influence of drugs, alcohol, or any medication that creates drowsiness or impaired thinking.
How do you adjust the tension on a belt sander?
If the belt is shifting toward the side of the sander that the knob is on, then loosen the knob by turning it about half a turn counterclockwise. If the belt is shifting away from the side of the sander that the knob is on, tighten the knob by turning it about half a turn clockwise.
What type of glue is used to make sanding belts?
Lay one end of the belt, grit-side down, on the bench; then apply cyanoacrylate glue to the end of the belt. Lay half of the bias tape’s width on the glue, place waxed paper over the tape, and use a weight to press down on it for about 30 seconds, or until the glue sets.
What tape is used on sanding belts?
Apply the Scotch 8959 tape by using a small piece of swimming pool noodle or other firm foam/rubber like a squeegee pressing firmly and leaving overlap on both ends, make sure there are no air bubbles and the tape is perfectly flat covering both splice ends equally.
Can you cut sanding belts?
You can cut sanding strips from sanding rolls or sanding belts. Cutting from sanding rolls is the more ideal solution.
What is belt sander good for?
What are Belt Sanders? Belt sanders are multiuse tools. They are commonly used for trimming to a scribed line (photo), sanding very rough surfaces, leveling surfaces (like a replacement board in a hardwood floor) and freehand rounding and shaping.
How are sanding belts measured?
Wrap it around the belt sander the same way you would put a belt on it. Cut the string so the ends meet up and then measure the string from end to end. To determine the width of the belt, you can measure the width of the roller or contact wheel the belt will run against.
What are the 3 most important sander safety rules?
Safety Rules Dust mask advised. Don’t wear loose clothing or gloves, keep long hair tied back. Never adjust Sander or setup while Sander is running. Never remove guard unless authorized by Technician or WRL Manager • Setups requiring anything other than the standard sander equipment must be approved by supervisor.
What may happen if you use too much pressure on the sanders?
Avoid pushing down with too much pressure on the sander. However, doing this can cause issues like swirls, cut-through, uneven sanding and other problems, such as excess heat and loading.
When changing sanding belts or discs what should be done to the belt disc sander?
When changing sanding belts or discs, what should be done to the belt/disc sander? Disconnect the machine from the electrical service. On most disc sanders the table can be adjusted ___________ degrees. 45.
Can belts be repaired?
Belt repair can be complex, as each job is custom and completed by hand. Often, our craftsmen must sew through thick layers of leather to make a delicate repair.
Is CA glue the same as Super Glue?
Cyanoacrylate glue, or CA for short, is commonly known by trade names such as Super Glue and Krazy Glue. It is an extremely strong and fast-setting adhesive available in three viscosities: thin, medium, and thick. Thinner glues have faster set times, while thicker versions have better gap-filling abilities.
What is in Krazy Glue?
Krazy Glue contains 99.95% ethyl cyanoacrylate and 0.05% acrylic. Krazy Glue is a clear, colorless liquid before curing. Cyanoacrylates are quickly polymerized by exposure to moisture and ultraviolet light. When cured, it forms an extremely strong bond that is fairly insoluble.