Premium blades have hardened teeth, and they far outlast ordinary blades. We tested all the premium resaw blades we could find that can safely be used on a 14-in. If you do a lot of resawing, you may find bi-metal blades worth the extra money because the extra-hard teeth are designed to outlast hardened carbon-steel blades.
The Wood Slicer Resaw Bandsaw Blade by Highland Woodworking has been the gold standard blade for resawing for many years. If you go to the Wood Slicer Resaw Bandsaw Blade page on the Highland Woodworking website you will see a full description of the blade. The carbon-manganese spring steel bodies provide a high amount of tensile strength to the blade and the Wood Slicer blade is unconditionally guaranteed against breakage at the weld.
Having the best blade for resawing is crucial if you want the best outcomes. We wanted to put resawing blades in the spotlight, to give you the lowdown on exactly which bandsaw blades are the best. Choosing the best bandsaw blade for resawing presents so many options.
At.025″;, Timber Wolf blades are about 25% narrower than most other band saw blades. These blades cut using much less tension than “Standard” band saw blades. No, you can’t run just any blade under less tension and try to get the same performance as the Timber Wolf blades.
There is no doubt the Timber Wolf Bandsaw Blade is an ideal bandsaw blade for resawing. “For a decent resawing bandsaw blade, we recommend a maximum blade thickness of 0.025 inches. Otherwise there might be a problem with tensioning and metal fatigue. Thinner blades have narrower kerf and are used for special jobs such as veneer sawing or resawing tasks.”Most 14″ saws are just not built to properly tension a blade thicker than.025” and the thicker the blade the more tension it takes to make it work properly. We hope our reviews of the best bandsaw blades for resawing, has addressed what makes a bandsaw blade suited specifically for this purpose.
resaw bandsaw blade reviews Related Question:
What bandsaw blade is best for resawing?
Resawing involves making rip cuts in the face of a wide board. So just like you would on the table saw, you’ll want to select a blade with fewer teeth per inch (TPI) than the blades you use for crosscutting or cutting curves. For most 14″ band saws, a 1 ⁄ 2 “-wide blade with 2-3 TPI is a good choice.
What should I look for in a resaw blade?
The article analyzed the most important features that help determine the performance of a resawing blade, namely blade thickness, blade width, number of teeth per inch, tooth form and durability.
How many teeth do you need to resaw a blade?
Typically, a wide 3-tooth-per-inch (tpi) blade provides the perfect blend of aggressive yet smooth cut and sawdust evacuation that resawing requires.
What size bandsaw do I need for resawing?
To get started with resawing, I recommend a band saw of sufficient power and with a large depth of cut. Any motor smaller than 1hp and depth of cut less than 10″ will limit your effectiveness. (Some 14″ band saws have about a 6″ maximum cutso you’d be limited to a 12″ wide book-matched panel or less.)
Can any bandsaw resaw?
Just about any bandsaw will do acceptable resawing. For example, all the cuts made in this story were done on an inexpensive, 14-in. bandsaw with a 3/4-hp motor. All we did to the saw was add a riser block to increase its capacity.
How much horsepower do you need to resaw?
A 3/4 or 1 HP bandsaw is pefectly adequate for re-sawing stock at home….
What causes bandsaw blade drift?
Drift is cause because the blade buckles under the load. You can see that by stretching a ribbon between 2 points and applying a pressure to one of the edges, it will turn sideway easily. A sharp blade and high blade speed will help a lot with that.
What does resaw mean on a bandsaw?
A resaw is a large band saw optimized for cutting timber along the grain to reduce larger sections into smaller sections or veneers. Resawing veneers requires a wide blade – commonly 2 to 3 inches (52–78 mm) – with a small kerf to minimize waste.
How long should a metal bandsaw blade last?
On average your bandsaw blade should last 6 months to as long as a few years depending on what your cutting with it. Make sure to match your blade strength and quality to the project and material your cutting.
Can I put a wider blade on my bandsaw?
An 18-inch diameter wheel can use a 0.032-inch thick blade that is 3/4 inch wide. In general, thicker and wider blades will be the choice when sawing dense wood and woods with hard knots. Such wood needs the extra strength of a thicker, wide blade to avoid breaking. Thicker blades also deflect less when resawing.
Is a wider bandsaw blade better?
The wider blades are stiffer overall (more metal) and tend to track better on the band wheels than narrow blades. When cutting thicker material, the wider blade has less ability to deviate because the back end, when in the cut, helps steer the front of the blade, especially if the side clearance is not excessive.
Why is it called resawing?
The reason for the different terms is that ripping cuts are all cuts along the grain but not all rip cuts are resawing. Resawing, as the term is used today, refers only to cutting a board across its thickness, i.e. sawing a thick board into two (or more) thinner boards.
How does a resaw guide work?
Resaw guides provide a higher level of control when adjusting for band saw blade drift. Curved face of the guide helps steer board into the cut. Easily attaches to the face of the band saw fence. This 7″ Resaw Guide is designed for larger capacity band saws.