I was upset that I couldn’t find the edge guide for Ryobi circular saw CSB125, so I called the company and they told me this is a substitute. It does not come with the screw needed to attach it, so I will be finding that in a hardware store.
Instructions: Secure your work piece and mark your cut. Align the line of cut with the 45° blade guide notch on the base when making 45° bevel cuts. Install the battery or plug the saw in and make your cut on the waste side of your cut mark.
Instructions: Secure your work piece and mark your cut. Align the line of cut with the 45° blade guide notch on the base when making 45° bevel cuts. Install the battery or plug the saw in and make your cut on the waste side of your cut mark.
No instructions included, but simply looking at the saw and the pictures from the manufacturer it was easy to figure out. The guide came with a lock down knob, although I ordered an extra one as it wasn’t clear that the guide came with the knob!
ryobi circular saw edge guide Related Question:
Are saw guide rails universal?
The YouTool Guide Rail is universally suitable for almost all brands of saw, and is available up to 5 meters long.
How do you use a circular saw without a table?
Fit your circular saw with an edge guide. Set the depth of the blade accurately enough for it to go through the wood and not cut under the surface. Place the guide on base of the circular saw lines and markings you made earlier on the wood. Ensure that the saw is free to move, and the power cord is not entangled.
Can I use any guide rail with a circular saw?
Obviously, it’s important to check that your circular saw is compatible with the guide rail you’re using, particularly if you’re cutting bevels. The risk you run is cutting into the guide rail itself. The GKS65 GCE’s bevel mechanism always keeps the blade away from the guide rail.
Can I use my circular saw as a track saw?
A circular saw can be used for all the same functions as a track saw, but doesn’t necessarily do them quite as well. If you’re on a budget, you can turn your circular saw into a makeshift track saw with straight edge guide.
How do I make sure a circular saw is square?
Making perfectly square crosscuts with a circular saw is easy, if you guide the saw with a layout square (a framing square or Speed Square will work). Hold the saw in place with its blade right on the cut line. Then slide the square against the saw’s base plate, and press it tightly against the edge of the board.
Why are my circular saw cuts curves?
Check whether the blade is parallel with the edge of the base, the edge that goes against the guide. If the blade is further away at the front, it’s going to want to walk away from the straight-edge. This is probably easiest to do when the base is in the 90 degree position rather than set at a bevel.
What size blade does a Ryobi circular saw?
Blade Size: 6-1/2 in.
How do you use a straight edge with a circular saw?
Slide the saw’s shoe against the circular saw rip guide to rip the plywood. To ensure a straight cut, press the saw firmly against the straightedge as you push it along. Clamp a perfectly straight board or metal straightedge to a sheet of plywood to make cabinet-quality straight cuts.
How do you use a circular saw without a sawhorse?
In some cases, it might be better to use your circular saw without a sawhorse. If you need to make cuts without a work support, you can lay a sturdy, stationary surface under the material while making cuts.
Why is my circular saw kicking back?
Overheating a saw blade can cause it to warp and result in a kickback. Buildup of sap on the blades, insufficient set, dullness and unguided cuts, can all cause an overheated blade and kickback. Never set a blade deeper than is required to cut the work piece 1/8 in. to 1/4 in.
Can you cut a 6X6 with a 10 miter saw?
A miter saw with a 10-inch blade installed can cut a 6X6 lumber piece, only it cannot do so with one single pass. This will require a bit more effort as the blade diameter is quite small for the piece of wood you are cutting. To do this cut with a ten-inch blade you’ll need to follow several steps to complete your cut.
How do you use saw guides?
Figure A: Straightedge Guide Glue the fence to the base, then run the saw against the fence to cut the guide. The factory edge is used for the fence. To use the guide, simply clamp it to the piece you’re cutting, aligning the base with the cut line.
Is it a guardrail or guide rail?
Guard rail is more common, but guide rail is acceptable. According to the US Federal Highway Administration, “The terms guardrail and guiderail are synonymous, and are used in different regions around the country.”[4] Guide rail and guard rail are intended to steer and “guide” vehicles back onto the road.
How much should I spend on a circular saw?
A circular saw can cost between $50-$200. Depending on your budget for the tool, you may want to go either cheaper or pricier. There are factors that can affect the price, such as brand or size. You will want to consider them when buying your own circular saw.
What is the difference between track saw and circular saw?
The critical difference is that a circular saw has a long and rectangular rail in the front, unlike its counterpart. A circular saw performs double cuts as the rip cuts and the crosscut, whereas the track saw three. The circular saw has a protective guard, whereas the track saw has none.
