stihl chainsaw how to videos Related Question:
How do you adjust the H and L on a STIHL chainsaw?
Determine the carburetor type before adjusting the high- and low-speed screws. To do this, turn the “L” screw clockwise as far as it will go, using a flat-head screwdriver, then turn it counterclockwise as far as it will go.
Where is the choke on a STIHL chainsaw?
The choke position is the fourth setting on the master control lever. This setting is used to start the saw when its motor is cold. Stihl chainsaws denote the choke position using a nearly horizontal squiggle between two vertical lines at the lowest position on the master control lever.
Why is my STIHL chainsaw not starting?
Dirty or clogged fuel tanks, dirty fuel filters and lines, loose fuel hoses, dirty air filters and a dirty carburetor can all restrict fuel flow. Check, clean and replace all the fuel system parts before moving into the internal engine, as gas problems create a majority of starting problems.
How do I start my Stihl chainsaw for the first time?
Press and hold the throttle trigger lockout (located on the side of the chainsaw, above the trigger) with your thumb, then move the master control (on the left of the rear of the chainsaw) down as far as it will go. This is the position you should start the chainsaw in the first time you use it each session.
Are Stihl chainsaws hard to start?
Regular maintenance will help to ensure that your Stihl chain saw will always start. In addition, some storage steps can help with starting when the chainsaw has been left for an extended period. Problems starting a Stihl chain saw can be related to gasoline storage, spark plugs, and incorrect starting procedures.
What does the L and H mean on a chainsaw?
The letters on the screws represent High (H), Low (L) and Idle (T). The H screw regulates the Air/Fuel mix during high RPMs, while the L Screw does the same during low RPMs.
What does H and La mean on a Stihl chainsaw?
One marked “H”, for high speed, one marked “L”, for low speed and one marked “LA”, which is your low speed air adjustment for idle.
What is a Stihl 311y?
The MS 311 is a high-tech workhorse with a step up in horsepower and features over the MS 291. With our improved engine technology, you get higher fuel economy for longer run times. The MS 311 also has larger fuel and oil tanks for even longer extended use. You’ll stay productive – while you’re saving money on fuel.
What is the choke on symbol?
The choke on symbol for most small engines looks like a horizontal ( — ) or diagonal ( / ) line. It also can simply say ‘Choke’, ‘Full Choke’, or ‘Start’. The off symbol for most small engine chokes is represented by a vertical line ( | ) or the word ‘Run’. Hopefully you have learned something here.
What is the choke position?
The choke is located before the throttle, and manages the total amount of air going into the engine. The choke is only used when starting a cold engine. When doing a cold start, the choke should be closed to limit the amount of air going in.
How long to wait if chainsaw is flooded?
Many people wonder if a flooded chainsaw will fix itself? The answer is yes, but not always. By letting the chainsaw sit for about 20 minutes it will allow some of the fuel inside the engine to evaporate.
Why does my Stihl chainsaw pull so hard?
If your chainsaw is hard to pull, here are some common causes: The pully system is snagged or stuck. The starter assembly is stuck or sticky. The housing may be damaged.
How do you test a Stihl chainsaw coil with a multimeter?
Locate the coil on your chainsaw. Connect the negative and positive cords of the multimeter to the negative and the positive terminals of the coil in your chainsaw and measure the resistance. A brief answer is convenient for those who are short of time but it will not give you the necessary details of the matter.
What does the LA screw do on a Stihl?
The LA setting on Stihl chainsaws is controlled by a screw on the outer housing of the engine that adjusts the flow of fuel and air through the carburetor. This screw is inside the engine housing on the carburetor, but is accessible through a hole or gap in the outer housing of the saw.
Why does a chainsaw cut crooked?
One major reason a chainsaw curves to either the right or left during a cut is that it was unevenly sharpened. The unequal teeth of the chain cause it to take a different-sized bite into the wood. What is this? The uneven sharpness of the chain is mainly due to manual sharpening, especially with the use of a file.