At.025″;, Timber Wolf blades are about 25% narrower than most other band saw blades. These blades cut using much less tension than “Standard” band saw blades. No, you can’t run just any blade under less tension and try to get the same performance as the Timber Wolf blades.
Their blades and the flutter method are pretty much my standard for bandsaw use. 11-05-2017, 10:19 AM #8 I pretty much “standardized” on the 1/2″ 3 tpi Timberwolf blade long ago based on how I generally use my MM16. I do have other format blades, but they rarely get used. 11-05-2017, 7:09 PM #13 Had good luck with the T-wolf blades myself.
About a year ago, I began noticing what appeared to be exaggerated claims regarding the capabilities of Timber Wolf band saw blades. Recently, while touring the Charlotte woodworkers show, in the midst of the over-amplified hucksters who mechanically rattled off occasionally wild overstatements regarding their product’s capabilities and equally overstated claims about competitors inadequacies, was an older gentleman calmly explaining how Timber Wolf band saw blades worked. Now, if Timber Wolf could figure out how to make their blades increase vertical re-saw capacity, there could be real trouble in the band saw retailing world.
timberwolf bandsaw blade reviews Related Question:
Is a wider bandsaw blade better?
The wider blades are stiffer overall (more metal) and tend to track better on the band wheels than narrow blades. When cutting thicker material, the wider blade has less ability to deviate because the back end, when in the cut, helps steer the front of the blade, especially if the side clearance is not excessive.
How long should a bandsaw blade last?
On average your bandsaw blade should last 6 months to as long as a few years depending on what your cutting with it. Make sure to match your blade strength and quality to the project and material your cutting.
What is the best size bandsaw blade for resawing?
Resawing involves making rip cuts in the face of a wide board. So just like you would on the table saw, you’ll want to select a blade with fewer teeth per inch (TPI) than the blades you use for crosscutting or cutting curves. For most 14″ band saws, a 1 ⁄ 2 “-wide blade with 2-3 TPI is a good choice.
What should I look for in a bandsaw blade?
Use coarse tooth blades (2 or 3 TPI) for re-sawing and cutting thicker materials. For general wood cutting duties in typical 3/4″ material, use a 4 TPI blade for coarse, fast cutting and a 14 TPI blade for slower, smoother cutting. A blade in the 6 to 8 TPI range provides good general-purpose performance.
How tight should my bandsaw blade be?
The blade should deflect no more than 1/4 in. A good place to begin is to tension the blade until the meter reads proper tension for the next wider blade. For example, if you’re tensioning a 3/8-in. blade, I would set the scale to 1/2 in.
Is more TPI better?
Woodworkers quickly learn that the number of teeth-per-inch (TPI) on the blade has a big impact on the quality of a cut. The general rule of thumb is “the more TPI, the smoother the cut.” The true answer, however, is just a little more complicated than that, as you’ll learn once you understand how saw teeth work.
What does TPI mean on a bandsaw blade?
You must select the correct Teeth Per Inch (TPI) for the thickness of material you are cutting.
What is the best TPI for cutting wood?
If you’re looking to cut wood or other soft materials, you’ll need a blade with a TPI of 6 up to 20. For harder materials like metal, a TPI between 14 up to 36 is more suitable. The number of teeth can be found on the blade.
How many times can a bandsaw blade be sharpened?
It often makes sense to replace a dull blade with a new one, but you can sometimes get the best value out of merely sharpening an old blade instead of replacing it altogether. You should typically be able to get two to three sharpenings before you need to change your blade completely.
Are bandsaw blades worth sharpening?
Since a carbide-tipped bandsaw blade will cost well over $100, spending a third of the cost of the blade (or more) to get it sharp and working like new again can make financial sense. However the majority of bandsaw blades, the Wood Slicer included, are not worth spending money to have sharpened.
How many times can you sharpen a sawmill blade?
You should be able to sharpen your blade two or three times before needing to replace it, but sometimes breakage happens. Blade breakage can result from a range of situations. Common causes of blade breakage include: Dull teeth.
What causes bandsaw blade drift?
Drift is cause because the blade buckles under the load. You can see that by stretching a ribbon between 2 points and applying a pressure to one of the edges, it will turn sideway easily. A sharp blade and high blade speed will help a lot with that.
What is resawing on a bandsaw?
Bandsaw Resawing from the beginning: resawing is cutting a sawn plank of wood into thinner planks on a bandsaw. Thus the cut runs through the plank’s width, which distinguishes bandsaw resawing from ordinary bandsaw rip cuts where the blade runs through the stock’s thickness.
What is the best TPI for cutting metal?
Cutting thinner metals, including sheet metal, requires a finer cut. Use 18-24 TPI bi-metal blades. For thicker metals such as steel pipe, angle irons, or tubing, use 14-18 TPI bi-metal blades. For aluminum, an 8-10 TPI blade is best.
Can a band saw cut curves?
Whether it’s a tight curve or a closed opening, you can cut it on your band saw with a couple of easy tricks. Cutting on the band saw can be the same thing. The narrower the blade, the tighter the spots you can cut; in fact, some band saw blades rival a scroll saw for cutting tight curves.