The tips are fragile, and because of that I can’t give them away to the pro’s around here who tried them, blew the tips fast, and now went back to things like the Stihl and Oregon bars. “The tips are a little brittle but are streets ahead of the Sugi Hara ones, since I made that reply I had a think and I would say I’ve more than likely used more than 3 tips per bar on the 28″s the others I use 36″ mostly hardwoods still original and the 24″ and 30” are now after a good bit of use need replacing in the very near future ! I’ve found the Oregon Powermatch bars just wear so much faster and become “Sloppy” after just a few weeks and at 80 euros for a 28″ I rather go through a bit of effort to get Tsu. “Hard to beat the Stihl ES.375” 13 tooth sprocket tip bars.
They help with balance the saws when running longer bars. When I started using them 3-4 years back the word was they are not as good as the regular weight Stihl bars. I have not found that they are less durable than standard weight bars.
Tsumura offers a number of guide bar models for Stihl chainsaws in the Medium and Large Stihl bar mounts. The Tsumura Stihl selection is quite limited and no bars are offered for Stihl Small mount saws. For more options, please check my Stihl bar data page and an earlier post on Oregon bars for Stihl.
He did not post the weight of a Stihl 20″ E bar. “These are the #s I got for 20”.050 bars:. Sugi 2 lb 3.1 oz.Stihl E bar 2 lb 4.6 oz. I have hefted 362s at the store with both 20″ E and 20″ ES bars on them, both Ver I & II. The ES bars make them very nose heavy. I would rather have a Ver I with a E bar than a Ver II with an ES. “Also, a 20” E bar has a list price of only $45.-.
tsumura chainsaw bar vs stihl Related Question:
Are Tsumura bars good?
Re: Tsumura Bars? A very good bar, I consider the best on the market. 2x 28″ which apart from 3x tips each ( I think !) still cutting well after around 3 years of pro use in all sorts of timber.
Do chainsaw bars make a difference?
Regardless of where they are made, there is a huge difference between the two brands of chain and bars. They use different formulations of steel with different hardness levels. I can tell the difference in the chains just by how they sharpen with a file.
Do Oregon bars work on Stihl chainsaws?
Chainsaw Bar & S55 Chain, Fits Various Stihl Models (105668) | Oregon Products.
How long should a chainsaw bar be?
The most common chainsaw bar sizes are 12 to 20 inches, but they come in sizes as large as 72 inches, typically for professionals. The longer the bar, the heavier the chainsaw.
Are Raisman chainsaw bars any good?
But even at the regular price, they are a great deal. I’m impressed that they balance so well on the 440, seem to be well made, and have a decent size Oil hole. I’ve been enlarging the oil holes on my Stihl Light bars, they are just too small. I have a 20″ Raisman bar on my Husky 257.
How often should you change the bar on a chainsaw?
If you are looking for a general idea for how often you should replace a chainsaw bar, a rule of thumb is to replace the bar of your chainsaw once after you have gone through three chains on the same bar.
Can you drill holes in chainsaw bar?
Re: Drilling a Chainsaw Bar Drilling that bar may not be as difficult as you think. It will be best if you use a drill press, start with a pilot hole, and then drill to the size you need. Make sure you have a sharp bit, run at the lowest speed you can, and use cutting fluid.
Why is my chainsaw bar smoking?
This most commonly is a result of a dull chain and exerting to much pressure on the bar and chain trying to make the chain saw cut. This could also be either a lack of bar and chain oil ( tank empty, restricted oiler hole ) or an inferior type of oil that is being slung off the chain and not lubricating.
Are Stihl chains better than Oregon?
Stihl chain hold their edge a bit longer than Oregon, but they also slightly harder to file. It is hardly noticable during normal maintnance (touch up before it gets dull), but obvious during more extended filing. I prefer Stihl when I have the option.
When should you throw away a chainsaw chain?
The chainsaw pulls in one direction, which results in a crooked finish. Blunt cutting teeth on one side or uneven teeth lengths usually cause this. The teeth has hit rocks or dirt and broken. If you notice the tops of the teeth are missing you will need to replace the chain.
Can I use a Husqvarna chain on a Stihl?
As a general answer, Husqvarna chains can go on a Stihl chainsaw. Though they can fit onto the Stihl chainsaw perfectly, these two chainsaw brands use different standard pitch sizes.
How big of a tree can a 20 inch chainsaw cut?
A good rule of thumb is that the diameter of the trees you cut regularly should be no more than twice the length of the bar on a chainsaw. That means a 20-inch chainsaw can handle a 36-inch tree (remember, effective cutting length is roughly -2 inches of the bar length).
How big of a tree can a 16 chainsaw cut?
16 chainsaw would cut through a 14″ tree diameter. 10 inch chainsaw for 8″ in diameter. 6 inch chainsaw can cut a 4″ diameter.
Who makes Oregon chainsaw bars?
Our History In 1947, the Oregon Saw Chain Manufacturing Corporation was founded with four employees and one product. Today, the Oregon brand is part of Oregon Tool, Inc, a corporation with more than 3,000 employees and thousands of products.
What kind of steel are chainsaw bars made out of?
The steel in most chainsaw bars is high-quality steel that will keep an edge well, but has enough flex to bend under stress rather than break or crack. The metal is generally corrosion resistant, and many bars are a stainless-steel alloy.