Chainsaw bar oil is a necessary component to operating your chainsaw at peak efficiency and with safety in mind. Formula Chainsaw bar oils are either petroleum-based or bio-based. ‘ Chainsaw bar oil for winter is usually 10W. Very hot temperatures may call for a thicker chainsaw oil, in the 40W to 50W range.
The reason a special type of chainsaw bar oil exists is that chainsaw chains and bars need a lubricant with certain qualities to keep those parts running smoothly. Motor oil will work to keep your chainsaw from burning up if you don’t have any standard bar oil on hand. Hydraulic oil is similar to motor oil and you can use it as a chainsaw bar oil substitute when you have nothing else available.
Unless you have a stockpile of gear oil available if your chainsaw oil runs out, it’s not a sound economic decision to buy gear oil as a backup. We recommend turning to canola oil as the best chainsaw bar oil substitute on our list. Chainsaw bar oil substitutes that derive from vegetables like canola oil are the best for your chainsaw.
what chainsaw bar oil to use Related Question:
Can you use any oil for chainsaw bar oil?
Generally, chainsaws can handle a wide range of lubricants. Vegetable and canola oils work well, and automobile motor oil will too, as long as you observe the SAE ratings and use the appropriate oil weight for the season. Always use fresh, never used, oils.
What kind of oil do you use for bar and chain on a chainsaw?
If your manufacturer’s bar and chain oil is unavailable, you can use SAE 30 weight motor oil to lube your chain during the summer and SAE 10 weight during the winter, according to the University of Missouri Extension.
Can I use 10w30 for chainsaw bar oil?
As a matter of fact, you can actually use regular 10w30 motor oil on a chainsaw as one of the alternatives in case you don’t have bar and chain oil. That’s because 10w30 oil has enough thickness and viscosity that will allow it to withstand the friction that is happening whenever you are using a chainsaw.
Can I use 5w 20 for chainsaw bar oil?
They are 5w20 and 10w30, which would be best? You can but it’s not very good for the chain or the environment. The Husqvarna / Stihl stuff is much thicker and vegetable based so it doesn’t fling off the chain as easily or poison your garden! 10w30.
Is bar and chain oil the same as motor oil?
Bar and chain oil is stickier than regular motor oil, so it stays on the chain longer. Motor oil flings off the chain more quickly, so if you try Terry’s tip, be prepared to refill the oil on your chain saw more quickly than with regular bar and chain oil.
Do Electric chainsaws need bar oil?
Electric chain saws derive their power from an electric source, so they don’t need fuel to run. Most gas chain saws require a premixed gas-and-oil fuel to operate properly. Electric chain saws don’t require this added oil, but the bar and chain do need to be properly lubricated.
What weight is chainsaw bar oil?
What viscosity is chainsaw bar oil? The viscosity of chainsaw bar oil can vary depending on the formula but 30W is standard. In cold weather, a thin 10W chainsaw oil may be advantageous, while very hot temperatures may require a much thicker 40W or 50W formula.
Can you use transmission fluid for chainsaw bar oil?
On occasion I’ve used tranny fluid to clean out old oil residue in old chainsaws . It works well . In addition to that tranny fluid seems to pump better on some saws with whimpy oilers in cold weather .
Can I use 2 stroke oil for chainsaw?
Can I use any 2 stroke oil in my chainsaw? No, you can’t use any 2-stroke oil in your chainsaw. Some 2-stroke oils are built for motor oils, and this might damage your chainsaw. Also, 2-stroke oils for an air-cooled engine are different from a water-cooled engine.
What happens if you run a chainsaw without bar oil?
Without lubricant, the speed at which the chain moves over the chainsaw bar can cause some serious friction. A slowed-down chain and excessive fuel burning mean there’s a lot of friction between your bar and chain, which means a lot of heat is being produced that could do major damage to your saw.
Can I use engine oil as bar oil?
It might be OK for a bit but I probably wouldn’t do it. You could look up your owner’s manual to see if they say anything. If you must use the chainsaw and have nothing else on hand, surely motor oil is better than nothing. I think bar oil is stickier than regular motor oil to prevent splattering as much.
What is special about chainsaw oil?
Chainsaw bar oil has a certain level of “slickness” to it. This slickness keeps the chain spinning at a fast rate without getting slowed down by the friction that occurs when metal rubs against metal. So, if you want to use the “correct” type of bar oil in your chainsaw, consult the manual and use what it suggests.
What kind of oil does a Poulan electric chainsaw use?
Ideal Oil. Poulan encourages customers to use its own brand of 2-cycle oil for air-cooled engines, most commonly found in 3.2 ounce size. Poulan brand oil is was designed specifically for its chainsaws and thus it is the only oil the brand guarantees.
What does 10W30 mean?
The 10W30 designation on engine oil means that the viscosity of the oil is rated at 10W when an engine is cold and 30 when the engine is hot. This is different than an oil labelled 5W30, which has a thinner viscosity when the engine is cold at 5W.
Can you lube transmission oil as chain?
Yes definitely you can use. I have been using gear oil of 140 grade on my dominar400 since past 9months. But before lubricating the chain make sure you clean the chain with diesel and wipe it with a cloth then apply the gear oil. I found gear oil to be better than chain spray.