Common reasons behind chainsaw overheating are a wrong oil/fuel mixture, a blocked or clogged exhaust. Overheating from a dull chain usually isn’t enough to cause serious damage to the chainsaw on its own. Never cut trees too big for your chainsaw as it can cause overheating and other serious issues.
Depending on how dull the chain is, this can even cause the chainsaw to overheat due to the huge amount of force it needs to put out all the time. To prevent dust from getting into the engine, chainsaws have an air filter installed. Most chainsaws use the 1:50 oil/fuel ratio, but always check your user manual for the ratio recommended by the manufacturer.
what causes chainsaw to overheat Related Question:
Why is chainsaw getting hot?
Overheating Chainsaw Blade The two most common causes of the overheating or smoking of your blade are lack of lubrication of the bar guide or the engine and lack of air.
Why does my chainsaw stop running when it gets hot?
When your chainsaw quits after it gets hot, you either have a problem with gas flow being restricted into the engine or with the spark. This is a common occurrence on older-model chainsaws. By replacing your spark plugs and keeping your gas lines clear you can reduce the chances of this problem recurring.
Why is my chainsaw burning the wood?
Your chainsaw burns wood because of poor lubrication Lubrication allows the mechanical parts to coordinate much better by avoiding a phenomenon of friction which risks causing traces of burns. This is one of the main reasons that your appliance gives off too much heat and that the wood burns.
How do I know if my chainsaw spark plug is bad?
If it’s not producing any sparks at all, your chainsaw needs a new plug. If there are only a few sparks coming out of one side of the electrodes but none on the other side, it’s not bad enough for you to worry about, but it will affect your performance.
When should you throw away a chainsaw chain?
The chainsaw pulls in one direction, which results in a crooked finish. Blunt cutting teeth on one side or uneven teeth lengths usually cause this. The teeth has hit rocks or dirt and broken. If you notice the tops of the teeth are missing you will need to replace the chain.
How often should you replace your chainsaw chain?
The chain sprocket must be replaced if the depth of the wear marks reaches about 0.5mm, i.e. the wear limit. A seriously worn chain sprocket can cause the chainsaw chain and guide bar to wear at an increased rate, as well as reducing cutting performance too, so it’s important to keep an eye on.
How many times can a chainsaw chain be sharpened?
Cutters can be sharpened up to 10 times or more before the chain needs replacing. If your cutters are worn unevenly after a few sharpenings, a professional can regrind them to uniform shape. If you use the same chain for a few years, then buy a new one, the new one won’t mesh smoothly with the sprocket and bar.
Can you over tighten a chainsaw chain?
There is a tension screw located near the base of the bar on the chainsaw. To tighten the chain, turn it clockwise, and to loosen turn it counterclockwise. Don’t over-tighten the chain as this could cause it to break.
How often do you need to sharpen a chainsaw?
A chainsaw may only need to be sharpened once a year if it is rarely used, but a tool that is frequently used will need to be sharpened regularly to ensure that the blade doesn’t get too dull. On average, a chainsaw blade will retain its sharpness for about 3 hours of actively cutting through wood.
How often should you change the spark plug in a chainsaw?
A poorly functioning engine in a Stihl chainsaw can mean more work for the operator and can even be dangerous. Consequently, Stihl recommends replacing the spark plug after every 100 service hours.
How often should spark plugs be changed?
Spark plugs are somewhat durable components and don’t need to be replaced too often, that said, the general recommendation is about every 30,000 to 90,000 miles. Each vehicle may differ on when they should be replaced.
How do you start a stubborn chainsaw?
Try to start the chainsaw after priming the carburetor. 5. Activate the choke by moving the lever to the full choke position and pull the starter rope 3 or 4 times to start the engine. If that doesn’t work, move the choke lever to half choke and pull the starter rope, 6 times maximum, to start the engine.