Even though the last blade is the one you should definitely get if you’re looking for the best, this is a good backup circular saw blade that you should have lying around in case the Freud one breaks. Without further ado, here’s our runner-up, the Enertwist 4-1/2 Inch Circular Saw Blade Set. These blades measure 4-½-inches, meaning they’re designed for smaller circular saws, but they are compatible with a lot of famous manufacturers, such as Rockwell, Worx, and Tacklife, and Enertwist, of course.
Besides looking at how to cut laminate countertop, we will also help you choose the right saw blade so that you will be able to cut the laminate much more comfortable. Now to the meat and potatoes of the article – how to cut laminate countertop with a circular saw using a blade we described above. So there you have it, this is how to cut laminate countertop with a circular saw.
You do not need to have a powerful router and accessories to cut a kitchen worktop to size at the corner. To create a clean, precise corner solution, as shown, you need a special worktop template, a cutter and a particularly powerful router to connect the kitchen worktops. The only disadvantage of mitre joints: If you have a worktop with a depth of 60 cm, you need a worktop that is 60 cm longer.
Once your worktops have been planned/set out you can start to cut worktop to length ready to join or edge them up. Always start the saw away from the material and once running at full speed and starting from the front edge of the worktop cutting towards the back slowly cut the worktop. Set the depth of the cutter to 5-8mm and when the router is at full speed start to cut worktop to length by sliding the router along the straight edge.
I have installed a couple of kitchens including laminate worktops. Most cheap routers have a 25mm cutting blade which has a 6.35mm diameter shank. These can accept a 50-60mm long cutting blade which saves time, see further on here…. As I said the 25mm blades mean I had to cut the worktops twice, once on the reverse and the final time from on to.
what circular saw blade for kitchen worktop Related Question:
What is the best circular saw blade for cutting worktops?
If you use a circular saw, it’s best to use a fine-toothed narrow blade with at least 40 teeth. When it comes to cutting laminate countertop, blades with carbide tips usually last longer than regular steel.
What blade Do I need to cut a worktop?
For solid and veneered worktops, you need a cross-cut, fine tooth saw blade with 48 teeth. For laminated worktops, it is advisable to use the triple chip grind saw blade, also with 48 teeth. In addition to the using the right saw blade, a splinter guard is essential for ensuring a low-splinter cut.
Can you cut a worktop with a circular saw?
A circular saw is often the best option to cut laminate worktops. Make sure the blade is sharp (replace the blade if you have been using it for a while) and suitable for fine cuts—it should cut through the worktop without any issue.
What kind of blade do you use to cut laminate countertop?
Cutting a post-form laminate countertop to length requires a clean, straight cut. The best DIY tool for the job is a circular saw with a fine-tooth carbide blade made for laminate (the same blades are typically sold for non-ferrous metals and other types of plastics). You can also use a jigsaw with a fine-tooth blade.
What is the best saw for cutting kitchen worktops?
Circular Saws A circular saw is the most efficient tool for cutting a worktop down to size.
How can I cut my countertop without chipping?
You can minimize the potential for chipping if you use a finish blade with lots of teeth, making sure the sharp is keen. You can further reduce the chance of chipping by using masking tape along the cut line and cutting through the tape. As with all cutting, measure at least twice and mark the line well and clearly.
What do I need to cut a kitchen worktop?
The best tool for the job, which is almost impossible to do without, is a circular saw. As long as the blade is suitable for fine cuts and sharp then it shall cut through laminated chipboard or hardwood kitchen worktops like a hot knife through butter.
What is a 40 tooth saw blade used for?
Deep gullets provide good chip removal. Crosscut blades, made for cutting across the woodgrain (across the face of a board), have between 40 and 80 teeth and are designed for clean cuts. Smaller gullets separate the teeth. Combination blades can make both rip cuts and crosscuts.
How many teeth do I need to cut a laminate countertop?
This 80-tooth blade is an excellent choice for cutting laminate, as well as hardwood, plywood, and softwood. Don’t be fooled by the small appearance of the blade; while it does seem smaller than some other blades, the performance will probably be even better for it.
Can you cut a kitchen worktop with a hand saw?
it is best to use a circular saw for cutting work tops to length, and if so work from the bottom of the worktop, NEVER from the top, as the teeth on a circ blade cut UPWARDS..and also cut from the front bullnose or what ever face shape, as if you start from the back you risk breakout from the front…but never use a …
Do you need a special blade to cut Formica?
Carbide router bits, jigsaw blades and circular saw blades will all work well on formica if proper guides and blade settings are used.
Is a plunge saw the same as a circular saw?
A plunge saw is like a circular saw with a blade that spins and cuts, only with much more sophistication and accuracy. Rather than the guard retracting to expose the blade when cutting, such as with a circular saw, it has a fixed guard and the blade is exposed when plunging the handle to the pre-set depth.
Can I cut laminate countertop with a jigsaw?
Use the starter holes to start the interior cut. Insert the jigsaw blade inside the hole, aligning the blade with the cutting line while keeping the show flat against the laminate countertop. Turn on the jigsaw and let the blade get up to speed, then steadily move the blade against the material.
How do I choose a circular saw blade?
Generally, blades with more teeth will provide a smoother, finer cut whereas blades with fewer teeth will provide a rougher cut. The benefit of fewer teeth is faster cutting and a lower price. For most construction work, a 24-tooth general use blade is sufficient.
Can I put a metal cutting blade on my circular saw?
Only blades and discs specified for cutting metal should be used. These professional circular saw blades are perfect for cutting through aluminium, copper, lead and other non-ferrous metals; while these diamond cutting discs will make light work of cutting through stainless steel.
