The first one on my list of the best miter saw blade for composite decking is the Wen BL1040. After digging a little bit more about it, I couldn’t resist including it in my list of the best miter saw blade for composite decking. If you are looking for the best miter saw blade for composite decking then consider the Norske Tools NCSBP228.
Miter saw blades, circular saw blades, and table saw blades are recommended blades for cutting composite decking. Circular Saw Blades: Circular saw blades are disc shaped blades that can cut through composite decking by spinning and with sharp teeth. The capacity of the blade will determine how deep into the composite decking you can cut, with larger saw blades making deeper cuts than others.
The blade can be applied to cut cellular PVC. One can easily get melt-free cuts with this blade that adds to the value of the finished product. The 64 teeth of the blade are 10 inches long that designed to cut through any decking material and even cellular PVC. The kerf design is ultra-thin, and the non-stick coating protects the blades while reducing drag. A circular saw blade with a high tooth count is ideal to cut composite decking.
what circular saw blade for composite decking Related Question:
What saw blade for composite decking?
Diablo’s TrexBlade is the only recommended composite decking by Trex Company when cutting composite decking materials. These new blades deliver maximum performance and highest quality of finish; making it a ‘must-have’ tool for both professionals and DIYers planning composite decking projects.
Can you cut composite decking with a circular saw?
How to Cut & Fasten Composite Decking. You can make simple cross cuts in composite decking the same way you would cut any soft pine—a power circular saw will work fine. A power miter saw can provide very accurate, straight cuts, and a table saw with support extensions can make all types of cutting easier.
Do I need a special blade to cut composite decking?
Yes, you can cut most composite decking just like wood — no special tools required.
What is the best way to cut composite decking?
Cutting The Deck Use a wood saw to cut the single pieces of the composite material to length and then mark the board using a quick square. You can either use a miter saw or a circular saw since composite cuts similarly to wood. Mark the board using a quick square while holding the square against the board’s face.
What is a 40 tooth saw blade used for?
Deep gullets provide good chip removal. Crosscut blades, made for cutting across the woodgrain (across the face of a board), have between 40 and 80 teeth and are designed for clean cuts. Smaller gullets separate the teeth. Combination blades can make both rip cuts and crosscuts.
What saw is best for cutting decking?
A circular saw is often used for most cuts, making it the best saw for deck building. Get one that cuts reliably, and equip it with a sharp carbide-tipped blade.
How many teeth blade for composite decking?
What is the Best Saw Blade for Cutting Composite Decking? The EnviroBuild installation guide advises the use of a circular saw using a 40 tooth alternate top bevel finish blade to cut your composite decking boards.
Can you cut composite deck boards?
Cutting composite decking is quite similar to cutting regular lumber. You can use a couple different saws including a circular saw, miter saw, or a table saw. The round blade is key to getting straight clean cuts that do not warp the board from excessive heat.
What is a TCT blade?
A TCT (Tungsten Carbide Tipped) blade is a resharpened circular saw blade. TCT saw blades can be used for the following items: wood, some ferrous metals, non-ferrous metals and plastics. Typically, a saw blade is a toothed blade designed to cut metal.
Do you need to leave a gap between composite decking boards?
As temperatures fluctuate, composite deck boards will naturally experience thermal expansion and contraction. That’s why the board ends should never be installed tight against one another. There should always be a slight gap.
Can you cut composite decking with a jigsaw?
Composite Decking. Diablo’s carbide teeth jig saw blades deliver extreme durability and superior cutting life in composite decking materials. High-performance carbide teeth provide an unmatched up to 50X longer cutting life versus standard jig saw blades.
What is a 60 tooth saw blade used for?
A crosscut blade, on the other hand, is designed to produce a smooth cut across the grain of the wood, without splintering or tearing. This type of blade will usually have 60 to 80 teeth, and the higher tooth count means that each tooth has to remove less material.
Can I use a bigger blade on my circular saw?
The answer is generally this is not a great idea. A larger blade will put excess stress on the motor, and may not have enough strength to provide the cutting power at the tooth you need.
What is a 24 tooth blade used for?
For most construction work, a 24-tooth general use blade is sufficient. That blade is very aggressive and will help you rip and cross-cut lumber and sheet goods quickly and with a high degree of accuracy. With a 24-tooth demo blade, you’re getting work done quickly, but you won’t get a near-finished edge.
How far apart should joists be for composite decking?
Most composite decking materials, like Trex, AZEK, TimberTech and Fiberon composite decking, require minimum joist spacing for composite decking at 16″ on-center spacing for straight decking and 12″ on-center joist spacing for 45-degree angle diagonal decking.
