Miter saw blades, circular saw blades, and table saw blades are recommended blades for cutting composite decking. Circular Saw Blades: Circular saw blades are disc shaped blades that can cut through composite decking by spinning and with sharp teeth. The capacity of the blade will determine how deep into the composite decking you can cut, with larger saw blades making deeper cuts than others.
The first one on my list of the best miter saw blade for composite decking is the Wen BL1040. After digging a little bit more about it, I couldn’t resist including it in my list of the best miter saw blade for composite decking. If you are looking for the best miter saw blade for composite decking then consider the Norske Tools NCSBP228.
The blade can be applied to cut cellular PVC. One can easily get melt-free cuts with this blade that adds to the value of the finished product. The 64 teeth of the blade are 10 inches long that designed to cut through any decking material and even cellular PVC. The kerf design is ultra-thin, and the non-stick coating protects the blades while reducing drag. A circular saw blade with a high tooth count is ideal to cut composite decking.
2.1 Circular Saw Blades: A circular saw blade is a disc with teeth that can cut composite decking utilizing a spinning motion. 2.2 Table Saw Blades: The table saw blade is one of the most important blades to consider when you want to cut composite decking. The table saw blade made for cutting composite decking has a special tooth design that allows it to cut through composite decking.
what circular saw blade for cutting composite decking Related Question:
What blade is best for cutting composite decking?
Diablo’s TrexBlade is the only recommended composite decking by Trex Company when cutting composite decking materials. These new blades deliver maximum performance and highest quality of finish; making it a ‘must-have’ tool for both professionals and DIYers planning composite decking projects.
Can you cut composite decking with a circular saw?
How to Cut & Fasten Composite Decking. You can make simple cross cuts in composite decking the same way you would cut any soft pine—a power circular saw will work fine. A power miter saw can provide very accurate, straight cuts, and a table saw with support extensions can make all types of cutting easier.
Do you need special saw blade to cut composite decking?
Cutting composite decking is similar to cutting normal lumber; it just requires special saw blades. So when cutting composite decking, it is advisable to use saw blades that are convenient and flexible for cutting. The saw blades must also be sharp.
What is a 40 tooth saw blade used for?
Deep gullets provide good chip removal. Crosscut blades, made for cutting across the woodgrain (across the face of a board), have between 40 and 80 teeth and are designed for clean cuts. Smaller gullets separate the teeth. Combination blades can make both rip cuts and crosscuts.
What saw is best for cutting decking?
A circular saw is often used for most cuts, making it the best saw for deck building. Get one that cuts reliably, and equip it with a sharp carbide-tipped blade.
How do you cut deck boards with a circular saw?
Hold the saw against it and check the blade is in on the desired finished line. Set the circular saws depth to the thickness of the deck boards, and slowly run it along the deck removing all the ends in a nice straight, equal line.
Is composite decking hard to cut?
Yes, composite decking can be cut to size easily. Follow these steps or use our installation guide.
Can you rip cut composite decking?
Trex products should not be ripped to reduce thickness, but can be ripped to reduce width. As long as the board can still be installed per the installation instructions, the warranty will be valid. Please use care when fastening ripped boards, as pre-drilling may be necessary.
Can I cut composite decking with a hand saw?
Like wood, you can use a conventional hand saw to cut composites. But it’s not efficient and will take a lot of time. You also need to make sure that it’s sharp.
What is the joist spacing for composite decking?
Most composite decking materials, like Trex, AZEK, TimberTech and Fiberon composite decking, require minimum joist spacing for composite decking at 16″ on-center spacing for straight decking and 12″ on-center joist spacing for 45-degree angle diagonal decking.
Can I use a bigger blade on my circular saw?
The answer is generally this is not a great idea. A larger blade will put excess stress on the motor, and may not have enough strength to provide the cutting power at the tooth you need.
What is a 60 tooth saw blade used for?
Honorable Mention: 60t or 80t Cross Cutting Blade A good cross cutting blade is designed to provide ultra-smooth cuts going across the grain without splintering or burning. And ultra-smooth cuts equate to better precision and tighter joinery in your projects. Generally, more teeth equals a better cut.
What is a 24 tooth blade used for?
For most construction work, a 24-tooth general use blade is sufficient. That blade is very aggressive and will help you rip and cross-cut lumber and sheet goods quickly and with a high degree of accuracy. With a 24-tooth demo blade, you’re getting work done quickly, but you won’t get a near-finished edge.
How do you cut deck board edges?
Snap the cutting line on the deck. Then measure from the edge of your saw blade to the edge of your saw’s base. Mark that distance from the line and screw down a straight board. Run the saw’s base against the straightedge to cut the deck boards perfectly straight.
How do you cut gaps between deck boards?
To widen the gap between the deck boards run the saw forward lightly touching one side, then check for clearance. If the space is still too narrow, make a second pass on the other side. You may have to make several passes using the same process to widen the space between the deck boards for desired spacing.
