Band saw blade drift is a tendency of the blade to veer to the left or right while making a cut using the rip fence. The point of the last paragraph is that if the band saw is not set up properly and/or does not have a good quality, sharp blade installed and tensioned correctly, the chances of accurately adjusting for drift are minimal at best. Since there is little that we can do about blade drift at the blade, we adjust the fence to match the drift angle to essentially cancel it out.
Being a happy bandsaw owner has a lot to do with your approach to coping with the fact that a bandsaw simply will not cut straight, or, in the sage words of veteran woodworkers, “Adjusting for drift.” Even the top performing 14″ bandsaw on the market, Powermatic’s 14 Bandsaw 1791216K, comes with a no-frills fence with 4 bolts on top rather than easy and obvious thumbscrews or knobs that say, “Adjust me here!”. Making the bandsaw cut nice and straight with this fence is a snap.
There’s no doubt about it – a bandsaw is one of the tools in your shop that might cause you the most frustration. Every shop needs one, so whether you’re an amateur struggling with blade drift or a professional who is constantly searching for ways to improve your workflow, having a well-functioning bandsaw is worth it. No matter what size your bandsaw is, we offer the always-reliable Timber Wolf bandsaw blades that make perfect replacements and cost-effective upgrades.
My playing around over the past few years seems to confirm the suggestion that presuming a correctly sharpened and jointed blade that can/has cut straight that the onset of drift is mostly to do with position of the blade on the tyres – that if a previously straight cutting blade starts to drift that it’s probably that the blade has moved on to a different part of the tyre. The other possibility is that something other than normal wear has happened to make the blade cut differently off one side than the other if a problem suddenly kicks in – but it should keep on tracking OK with normal even wear. Prime suspect with a new blade on a saw that has previously been OK has to be a misaligned weld, or a badly sharpened blade…. ian.
If one side of the blade has more sets than the other or the blade starts to drift, check to see that the blade is properly sharpened and that the set is still good. After installing the saw blade, applying proper tension, and tracking adjustments, bring the fence next to the blade and see if the face of the fence is parallel to the blade body. The saw blade and machine can both stand more tension, but it isn’t advised nor a good idea to put too much tension on the blades.
what is bandsaw drift Related Question:
What causes a bandsaw blade to drift?
Drift is cause because the blade buckles under the load. You can see that by stretching a ribbon between 2 points and applying a pressure to one of the edges, it will turn sideway easily. A sharp blade and high blade speed will help a lot with that.
How tight should my bandsaw blade be?
The blade should deflect no more than 1/4 in. A good place to begin is to tension the blade until the meter reads proper tension for the next wider blade. For example, if you’re tensioning a 3/8-in.
What size band saw for resawing?
To get started with resawing, I recommend a band saw of sufficient power and with a large depth of cut. Any motor smaller than 1hp and depth of cut less than 10″ will limit your effectiveness. (Some 14″ band saws have about a 6″ maximum cutso you’d be limited to a 12″ wide book-matched panel or less.)
What band saw blade for resawing?
Resawing involves making rip cuts in the face of a wide board. So just like you would on the table saw, you’ll want to select a blade with fewer teeth per inch (TPI) than the blades you use for crosscutting or cutting curves. For most 14″ band saws, a 1 ⁄ 2 “-wide blade with 2-3 TPI is a good choice.
Why does my bandsaw cut to the right?
When the band saw cuts crooked, a dull blade, improper feeding, loose blade tension or not using a work piece guide could be the cause. Use the rip fence or miter gauge to guide the work piece uniformly through the cutting blade to make straight cuts.
Why does my bandsaw blade burn the wood?
A majority of issues with wood burning is because of a dull saw blade. These blades may not be sharp enough to efficiently cut the wood, and thus create enough friction to heat and burn the wood. What is this? Dull blades make it more challenging to cut, which causes friction as you pass the wood through.
Why do bandsaw blades break?
Even the best blades can fail if there is something else wrong with your bandsaw, and even a small misalignment of bearings or guides can put a twist in the blade as it goes around. Resulting in tension being applied in all the wrong ways which will lead to early breakage.
How long should a bandsaw blade last?
On average your bandsaw blade should last 6 months to as long as a few years depending on what your cutting with it. Make sure to match your blade strength and quality to the project and material your cutting.
Why are my bandsaw cuts wavy?
The clasic cause for wavy lumber is pushing a dull blade past it’s limits. Sharp don’t get it.
Which way should the teeth face on a bandsaw?
Installing A Bandsaw Blade Make sure the teeth point downward.
Can any bandsaw resaw?
Just about any bandsaw will do acceptable resawing. For example, all the cuts made in this story were done on an inexpensive, 14-in. bandsaw with a 3/4-hp motor. All we did to the saw was add a riser block to increase its capacity.
How thick can a bandsaw cut?
Band saws are the undisputed champ when it comes to cutting curves and slicing through thick material. Many small band saws can slice though lumber a full four inches thick, and bigger saws handle six-inch cuts.