Chainsaw Oil is specifically developed for the lubrication of chain and guide bars of modern chain saws. Chainsaw Oil has good low temperature flow properties which makes it suitable for outside applications even during the winter season. Chainsaw Oil can be used in hand-held or machine operated chain saws as specified by the manufacturer.
Heat from summer thins oil, and cold from winter makes it thick. To prevent this, chainsaw manufacturers make bar oils matched to the air temperature and the saw in which it is operated. Although they don’t disclose the weight of their oil, the University of Missouri Extension recommends in lieu of using a bar oil, select SAE 30 weight oil in summer and SAE 10 in winter.
At Gardening Products Review, we highly recommend oil manufactured for this specific use. Chainsaw shown in this video tutorial is the Redback 40V 12″ Li-Ion Cordless Chainsaw. The bar & chain oil featured in this video is Husqvarna Bar & Chain Oil – 1 Gallon.
Knowing the available chainsaw oil options, learning how to choose the right one and determining the right fuel/oil ratio can help ensure your chainsaw runs smoothly every time. Common Issues if Chainsaw Oil Is Bad. Chainsaw engine oil can go bad. Two-cycle oil is good for up to five years when sealed, and many manufacturers list the oil’s shelf life on the container. “One thing we do for our customers who buy a chainsaw that requires an oil/gas mix is we have them buy a gas can and we write the formula right on the can with a big black Sharpie. Then, the next time they need to make the mixture, they can dump in the right amount of oil and take the can to the gas station and pump in the right amount of gas.”
Chainsaw bar oil is a necessary component to operating your chainsaw at peak efficiency and with safety in mind. Formula Chainsaw bar oils are either petroleum-based or bio-based. ‘ Chainsaw bar oil for winter is usually 10W. Very hot temperatures may call for a thicker chainsaw oil, in the 40W to 50W range.
what is chainsaw oil Related Question:
Can regular oil be used as chainsaw oil?
Regular oil can be used effectively as a lubricant for chainsaw bars. It is because chainsaw bar oil isn’t rated by SAE Rating, unlike traditional motor oil. While summer and winter weights should be considered, SAE 30 should be used in the summer and SAE 10 in the winter.
Can you use any oil for chainsaw bar oil?
Generally, chainsaws can handle a wide range of lubricants. Vegetable and canola oils work well, and automobile motor oil will too, as long as you observe the SAE ratings and use the appropriate oil weight for the season. Always use fresh, never used, oils.
Can I use 10w30 for chainsaw bar oil?
As a matter of fact, you can actually use regular 10w30 motor oil on a chainsaw as one of the alternatives in case you don’t have bar and chain oil. That’s because 10w30 oil has enough thickness and viscosity that will allow it to withstand the friction that is happening whenever you are using a chainsaw.
Can I use vegetable oil in a chainsaw?
Effective – Vegetable oils have natural properties including good lubricity, resistance to shear, a high flash point, and a high viscosity index. These qualities lend themselves to chain lubricant requirements similar to petroleum-based chain oils, and do not contribute to chain or bar wear over time.
What is bar oil equivalent to?
Canola oil It is thinner than regular vegetable oil, meaning it will tend to fly off the chainsaw more quickly – but it has a more suitable viscosity at lower temperatures so makes a good substitute for chainsaw oil when it is too cold to use vegetable oil.
Do Electric chainsaws need bar oil?
Electric chain saws derive their power from an electric source, so they don’t need fuel to run. Most gas chain saws require a premixed gas-and-oil fuel to operate properly. Electric chain saws don’t require this added oil, but the bar and chain do need to be properly lubricated.
What happens if you run a chainsaw without bar oil?
Without lubricant, the speed at which the chain moves over the chainsaw bar can cause some serious friction. A slowed-down chain and excessive fuel burning mean there’s a lot of friction between your bar and chain, which means a lot of heat is being produced that could do major damage to your saw.
Can I use 2 stroke oil for chainsaw?
Is 2 stroke oil the same as chainsaw oil? Yes, 2-stroke oil is the same as chainsaw oil. However, a chainsaw engine could also be designed for a 4-stroke oil.
What is special about chainsaw oil?
Chainsaw bar oil has a certain level of “slickness” to it. This slickness keeps the chain spinning at a fast rate without getting slowed down by the friction that occurs when metal rubs against metal. So, if you want to use the “correct” type of bar oil in your chainsaw, consult the manual and use what it suggests.
Do all chainsaws need oil?
To run properly, all chainsaws need two types of oil for different jobs. The first is engine oil. The chainsaw shown here has a two-stroke engine, so it needs two-stroke engine oil mixed with the fuel to help cool and lubricate the moving parts inside the motor.
What viscosity is chainsaw oil?
What viscosity is chainsaw bar oil? The viscosity of chainsaw bar oil can vary depending on the formula but 30W is standard. In cold weather, a thin 10W chainsaw oil may be advantageous, while very hot temperatures may require a much thicker 40W or 50W formula.
Can you use 10w40 in a chainsaw?
You can but it’s not very good for the chain or the environment. The Husqvarna / Stihl stuff is much thicker and vegetable based so it doesn’t fling off the chain as easily or poison your garden! 10w30. Thicker.
Can you use sunflower oil in a chainsaw?
If using a saw to cut meat, then vegetable oil is the obvious choice so the meat tastes good (you can use sunflower, canola, palm oil etc).
Can you use old motor oil for chainsaw bar?
Some people caution against using motor oil on a chain saw, but not for safety reasons or concerns about equipment. Bar and chain oil is stickier than regular motor oil, so it stays on the chain longer.
How much chain oil does a chainsaw use?
When to Oil Gas chainsaws use about one tank of bar and chain oil for every tank of fuel, so fill the reservoir every time you fill the tank.