“I need a 7¼” blade to cut 4×8′ sheets of plywood for cabinets. Handle the saw carefully because the telescoping blade guard will not extend through the zero-clearance base to cover the spinning blade. Then retract the saw blade above the base, and attach the zeroclearance plate using double-face tape.
In general, many woodworkers either use combination blades or rip blades when cutting plywood, and both types of blades are perfect for plywood cutting. Given the many types of brands and models of circular saw blades in the market today, choosing the best blades become doubly difficult. A circular saw is a versatile tool, and as long as you are using the right blade, you can quickly cut through plywood using a circular saw and end up with a refined finish.
Make circular saw cuts so clean that you don’t have to sand or touch up the plywood edges. Cutting speed depends on many factors, including the type and sharpness of the blade and the type of plywood you’re cutting. Spike Carlsen, an editor for The Family Handyman, will show you how to cut construction grade plywood and finish grade plywood with a circular saw in our video tutorial.
The thin kerf and wide set teeth enable a blade like this to cut to softwoods like pine and pressure treated beams a little more easily. The excessively high tooth count cut very slowly, which actually can cause the blade to become pinched between the pieces being cut and cause burning. Not related to the cut itself, but the blade doesn’t have any relief cuts or stabilizer vents.
Its extremely thick hardened plate is the reason why the model is considered the best 7 circular saw blade for plywood. In the second position, we have nominated a miter/table saw blade from a highly popular brand called DEWALT for the best circular saw blade for plywood. Take hold of the saw blade for plywood before activating it and don’t release the blade until it’s turned off.
what size circular saw blade to cut plywood Related Question:
What circular saw blade is best for cutting plywood and why?
Best Circular Saw Blade: Ultra Fine Finish With 60 teeth and a . 059-inch kerf, the Freud D0760X Diablo Circular Saw Blade creates clean, smooth cuts on delicate material like veneer plywood and melamine. This thin kerf greatly reduces the chance of chipping and blowouts, and doesn’t waste any material.
What blade is best for cutting plywood?
To get the best-quality cuts, invest in an 80-tooth blade designed for sheet goods. The small teeth take little bites to reduce chip-out and are steeply beveled at their edges to score the veneer face. You’ll have to slow your feed rate, but will get a much smoother edge.
How many teeth should a circular saw plywood blade have?
Framing blades have 24 teeth and are effective for jobs such as rough carpentry, where speed is more important than getting a clean cut. Plywood blades have 100 or more fine teeth designed to create a finish with minimal splintering.
Can you cut plywood with a circular saw?
Circular saws can be used to make square, miter, bevel and compound-angle cuts. When fitted with the appropriate blade, it can even cut metal and concrete. However, there’s one job for which the circular saw is particularly well-suited: cutting large sheets of plywood down to size.
How do you cleanly cut plywood?
The best thing you can do to get clean cuts in plywood is to use a zero-clearance insert. This closes the gap around the blade in the throat plate or shoe. On a table saw, you can buy an aftermarket insert blank, or you can easily make one yourself.
Is more teeth on a saw blade better?
Blades with more teeth yield a smoother cut. Blades with fewer teeth remove material faster, but tend to produce a rougher cut with more “tearout”. More teeth means you will need to use a slower feed rate.
What do you put under plywood when cutting?
The Secret is 2×2 Foam Board Here I have 8 laid out to support a full sheet of 3/4″ plywood. And unlike full insulation sheets, they are so easy to store. I just stack them up on a top shelf or under my bench.
What is a 60 tooth saw blade used for?
A crosscut blade, on the other hand, is designed to produce a smooth cut across the grain of the wood, without splintering or tearing. This type of blade will usually have 60 to 80 teeth, and the higher tooth count means that each tooth has to remove less material.
What is a 24 tooth blade used for?
For most construction work, a 24-tooth general use blade is sufficient. That blade is very aggressive and will help you rip and cross-cut lumber and sheet goods quickly and with a high degree of accuracy. With a 24-tooth demo blade, you’re getting work done quickly, but you won’t get a near-finished edge.
What is a 140 tooth saw blade used for?
OVERVIEW. The CRAFTSMAN 7-1/4-in 140-tooth carbon circular saw blade is made for cutting plywood, OSB and plastic. With a fully hardened and fully flattened plate, along with 140 precision-ground teeth, this blade delivers precise cuts without chips or splinters in the wood or cracks in vinyl and plastic materials.
How many teeth do you need for plywood?
Cross-cutting wood or sawing plywood: Use a 40-tooth to 80-tooth blade.
Why does my saw blade burn the wood?
A dull blade will make it hard to cut quickly, and the slower the feed rate of the saw, the more friction against the wood and the greater the likelihood of scorch marks. Pushing the stock through the saw too slowly is a common cause of saw blade burn. Sometimes a blade that feels dull might only be dirty.
What is the best blade to use for cutting with the grain of the wood?
If you’re just cutting with the grain, you’ll want to use a rip saw blade. For cutting across the grain only, you’ll want a crosscut saw blade.
What TPI is best for cutting wood?
If you’re looking to cut wood or other soft materials, you’ll need a blade with a TPI of 6 up to 20. For harder materials like metal, a TPI between 14 up to 36 is more suitable. The number of teeth can be found on the blade.
How do you cut plywood without a blowout?
Install the proper blade on your circular saw for different kinds of plywood. For precision cuts on hardwood plywood such as in cabinetry, use a carbide-tipped blade with square-cut teeth. Known as a cross-cut blade, it cuts smooth and straight without chipping or splintering loose fibers.
