Buy a good circular saw now and you can expect to still be using it in 10 or 20 years. Many tool manufacturers now offer sets of power tools that use the same batteries, and if you already own several tools by one manufacturer, adding a cordless circular saw that uses the same batteries is an affordable option. A well-shaped handle and good balance can go a long way toward making a saw more comfortable and efficient to use, so don’t overlook these features when choosing a circular saw.
Power is what gives the saw cutting ability, the higher the power, the better, when it comes to choosing a circular saw. There are two figures used by manufacturers to rate the power of a circular saw in the UK and Europe Watts is used and in the US amperes are used. For cordless circular saws as with other cordless power tools, the Volts will determine how much power is available, the most common power supply or battery size for power tools is 18V. As I said before many top brands like Hikoki, DeWalt and Makita have invested in new Lithium-ion technology and offer much higher voltage cordless options that give a great cutting performance.
Bring the saw up to full speed, lift the guard, and slowly push the body of the saw down to start the cut. TIP: Make sure to start back far enough so that you only push the saw forward; never drag a spinning saw back. If a board is too wide for the saw shoe to hang over the edge during a rip cut, hold a narrow scrap of wood between thumb and forefinger, bracing your finger along the edge of the board, and butt the saw shoe against the edge of the wood scrap as you push both along the board.
what size of circular saw do i need Related Question:
How do I know what size circular saw to get?
Circular Saw Features Blade capacity determines the maximum depth of cut a saw can achieve. The larger the blade, the deeper the cut. The most common blade diameter is 7-1/4 inches. Most saws with blade capacities of 6 inches or more can cut through 2-inch dimensional lumber at a 45-degree angle in a single pass.
Can a 6.5 inch circular saw cut a 2×4?
The 6.5 will cut up to 2 1/16”, while the 7 ¼” cuts up to 2 ⅜”. Minor sure, but it’s when you tilt them into 45 degree angles, that the 7 ¼” can do something the 6.5 can’t. Cut through a 2×4.
What is the most popular circular saw size?
The most widely used circular saw is the 7 1/4 inch, but most refer to this saw as the 7 1/2-inch saw. If you have questions about it, either blade works. Look for the blade’s diameter on the side of the blade.
How deep can a 7 1/4 inch circular saw cut?
Circular Saw Sizes Standard-size saws use 7 1/4-inch blades and can cut a maximum depth of about 2 1/2 inches.
What size circular saw will cut a 4×4?
Cutting a 4×4 with a Circular Saw – Guide If you need to cut a 4×4 post, then the ideal tool is a large 12” miter saw. This saw has the blade diameter needed to chop through a 4×4 in a single pass, so if this is an option for you it’s the way to go.
How deep can a 6 1 2 inch circular saw cut?
The 18V Brushless Lithium Ion 6-1/2 Inch Deep Cut Circular Saw (C18DBALQ4) is a revolutionary cordless circular saw utilizing a 6-1/2″ blade which allows a 2-19/32″ cutting depth, making it one of the deepest cutting cordless circular saws on the market. This circular saw has a similar cut capacity as a 7-1/4″ saw!
How thick of wood can a 5 1 2 circular saw cut?
The blade, located on the left side, cuts up to 1-3/4-inch at 90 degrees and 1-3/16-inch at 45 degrees.
How thick of wood can a 6 1 2 circular saw cut?
Depth. A 6 ½ circular saw can cut materials up to 2.5 inches. It’s perfect for cutting small materials for a small DIY project.
Can you use a 7 blade on a 6.5 circular saw?
NO, a 7″ blade will not fit inside the blade guard. Also, it’s rough on these little saws cutting concrete or tile unless you reduce the blade size.
Can a 6 1 2 circular saw cut a 4×4?
Like miter saws that measure less than 12 inches, a circular saw’s 6.5-inch or 7.25-inch blade will not cut cleanly through a 4×4. The maximum depth of most circular saws is just 2.5 inches. This means you’ll need to make two cuts. Having to make two cuts makes it easier to set up the cut.
What is a 40 tooth saw blade used for?
We chose a 40-tooth blade for a balance of cutting speed and finish quality to produce a happy medium between the two sectors. Realistically, a dedicated trim carpenter would likely go for a 60-tooth blade while a framer would prefer the speed of a 24-tooth model.
What size circular saw Do I need to cut 2×4?
You need a minimum 5-3/8 inch size circular saw blade to cut a 2X4 at a 90 degree angle in one cut which is a crosscut. If you want to cut a 45 degree bevel with this size circular saw it will take 2 cuts. You could go with a 7-1/4inch or 10 inch blade to avoid making multiple cuts with the 45 degree bevel angle.
Will a 4.5 inch circular saw cut a 2×4?
The new WORXSAW Compact Circular Saw is capable of cutting a 2×4 in a single pass. The compact circular saw features a 4-1/2 in. blade that is up to 50 percent lighter than a full-size 7-1/4 in.
Can a 5.5 inch circular saw cut a 2×4?
The Ryobi cicular saw is a 5.5″ saw, and it can cut a 2×4, just barely.
How deep can a 12 inch circular saw cut?
To sum up, a standard circular saw can offer a cutting depth of 2.5 inches as the maximum, but you can adjust the depth to match your requirements. It’s easy by moving the blade up and down to align against the material before starting to cut.
