Not only will you need a different blade for cutting metal than you would for cutting wood, but a metal-cutting blade should not be used in the same saw as the type used for wood. If you do decide to use a wood saw on metal, only use a 7 1/4-inch blade and preferably a worm drive blade, which provides extra torque. As always when purchasing a blade for your circular saw, make sure it has the right diameter and arbor size to match your saw.
Cut Metal Fast There’s nothing wrong with using a good, old-fashioned hacksaw, but there are faster, easier ways to cut metal. Cut Aluminum with Your Miter Saw Making accurate cuts on aluminum rods, tubes and angles is easy with a miter saw and a blade designed to cut nonferrous metal. Cut Metal Lath and Mesh with a Grinder Metal lath and hardware cloth can be cut with a tin snips, but there’s an easier way.
Metal work can pop up when replacing or repairing HVAC ducts, restoring the metal flashing on a roof, or while preparing for a metal crafting project, such as building an outdoor shower or creating an accent wall. If using a chop saw, or any other stationary power tool, the metal should be lined up with the blade, prepared for you to begin cutting. Cutting metal pipe, or other long, narrow pieces of metal is simple with a chop saw, but if you are working with sheet metal, you will have a difficult time trying to run the entire width of the metal through a stationary chop saw.
Choosing the right blade for your circular saw is crucial if you want your circular saw to operate at peak efficiency. I will tell you about the different kinds of circular saw blades and what kind of blade is best for each job. Inexpensive: The circular saw blades are cheap compared to table saw blades.
what type of circular saw blade to cut metal Related Question:
What type of circular saw blade do you need to cut metal?
Ferrous blades are ideal for cutting metals that contain iron, such as stainless steel or cast iron. Choose a non-ferrous blade when cutting softer metals, like aluminum or copper. For the best results, use a diamond blade that’s rated to cut the type of metal you are working with.
Can I put a metal cutting blade on my circular saw?
Only blades and discs specified for cutting metal should be used. These professional circular saw blades are perfect for cutting through aluminium, copper, lead and other non-ferrous metals; while these diamond cutting discs will make light work of cutting through stainless steel.
Can you use any circular saw to cut metal?
Circular saw blades are more durable than regular stainless steel wheels, and there are different types of circular saws that can cut through different materials including metal, tile, and plexiglass. The same model (with the right blade) can go through both hardscape and soft scape materials without much effort.
Can I use a wood blade to cut metal?
While a metal-cutting saw has a collection bin to prevent metal chips from getting into the machine, a woodcutting saw isn’t designed this way. If you do decide to use a wood saw on metal, only use a 7 1/4-inch blade and preferably a worm drive blade, which provides extra torque.
What is a 40 tooth saw blade used for?
Deep gullets provide good chip removal. Crosscut blades, made for cutting across the woodgrain (across the face of a board), have between 40 and 80 teeth and are designed for clean cuts. Smaller gullets separate the teeth. Combination blades can make both rip cuts and crosscuts.
What is a 60 tooth saw blade used for?
A crosscut blade, on the other hand, is designed to produce a smooth cut across the grain of the wood, without splintering or tearing. This type of blade will usually have 60 to 80 teeth, and the higher tooth count means that each tooth has to remove less material.
Can carbide blade cut metal?
Tungsten carbide, called simple “carbide” in the building trades, is three times harder than steel; and when placed on circular saw blades, reciprocating saw blades and grinder discs, tungsten carbide cuts cleanly through steel.
What is the best tool for cutting metal?
Hacksaws can cut through a pipe, metal stock, and heavier gauge sheet metal, and they leave a relatively clean cut that’s easy to refine. You’ll need a good bit of elbow grease when using a hacksaw, but for making straight cuts, they’re one of the most helpful metal cutting tools.
What is a HSS blade used for?
HSS Saw Blades are designed for cutting non-ferrous metal and plastic where maximum cutting life between sharpening is required . Ideal for sawing a wide variety of sizes and shapes such as extrusions, tubes, sheets, plates and some bar stock.
Can you put an angle grinder blade on a circular saw?
The exposed blade can cause significant injuries as the uncontrollable tool flies backwards and strikes the operator. For these reasons, angle grinders must never be fitted with circular saw blades.
Can carbide tipped blade cut aluminum?
Cutting aluminum with a circular saw requires a few special steps. Ensure that you have the right blade. A carbide blade works but is more likely to grab the material. If possible, purchase a blade specially designed for cutting aluminum and other non-ferrous materials.
Can you use a circular saw to cut aluminum?
A blade you use for woodworking will work on an aluminum application. However, you will need to ensure that the blade has carbide tips, and it is necessary to be more cautious with metal. That is because the tips can get ahold of the material, which will destroy the cutting piece or the blade.
Is more teeth on a saw blade better?
Blades with more teeth yield a smoother cut. Blades with fewer teeth remove material faster, but tend to produce a rougher cut with more “tearout”. More teeth means you will need to use a slower feed rate.
Can Diablo blade cut aluminum?
Diablo’s Aluminum saw blade series is ideal for corded and cordless saws when on-the-job cutting non-ferrous metals such as aluminum extrusions, copper pipe, brass plate, etc.
How many teeth do I need on my circular saw blade?
Number of Teeth Generally, blades with more teeth will provide a smoother, finer cut whereas blades with fewer teeth will provide a rougher cut. The benefit of fewer teeth is faster cutting and a lower price. For most construction work, a 24-tooth general use blade is sufficient.
