The correct carburetor adjustment will allow the saw to produce maximum power, extend the duty cycle of the engine, produce minimal smoke, idle smoothly, rev up nicely and give trouble free service. High Speed Fuel Adjustment – This is the adjustment that controls the proportion of fuel in the combustible air/fuel mixture at cutting speed. If carburetor adjustment is required due to a new or rebuilt carburetor, it is best to start with the fuel adjustment settings one turn out.
It would not be accurate to say this is the most important setting, because all of these adjustments need to be accurate for a saw to perform its best, but this is the adjustment that determines how the saw runs in the cut. If you adjust your saw with a dirty air filter, the saw will run too lean when the filter is cleaned. If proper adjustment for your saw is outside the limited range, take your saw into a shop.
How to Adjust the Carburetor on a Poulan Pro Chainsaw. Adjusting the Homelite chainsaw carburetor involves tuning the idle speed screw. Adjust the screw labeled ‘L’ until the chainsaw accelerates smoothly and sounds smooth.
when to adjust chainsaw carburetor Related Question:
How do you know if your chainsaw is running lean?
If your chainsaw is running lean, it will take a long time to return to idle once you rev it up at a high rpm. Idle means the chain isn’t spinning even though the engine is on. Also, the saw will work at a higher rpm than recommended, but it will have less cutting power due to the lack of gas in the mixture.
Why does my chainsaw bog down when I give it gas?
If your chainsaw is bogging down when you give it throttle, this is often a sign of improper gas-to-oil ratio. If there is too much gasoline in relation to the amount of oil used, this is known as a “rich mixture” and can cause the chainsaw to run poorly.
Why does my chainsaw start and then stop?
A clogged carburetor is often caused by leaving fuel in the chainsaw for a long period of time. Over time, some of the ingredients in the fuel may evaporate, leaving behind a thicker, stickier substance. This sticky fuel can clog up the carburetor and cause the chainsaw engine to stall.
What is the T adjustment on chainsaw?
The T screw regulates how much fuel is sent to the carburettor while idling until the throttle is pressed. L Screw – With the chainsaw still running, take a screwdriver and turn the L screw clockwise. Keep turning it until the engine almost stops turning.
What do the high and low screws do on a chainsaw?
Most Pro Saw Engines Have Three Carburetor Adjusting Screws: If this adjustment is set too low, the engine will die when the throttle trigger is released. If this adjustment is set too high, the high idle speed will cause the centrifugal clutch to engage and the chain will run.
Why does my chainsaw only runs on choke?
When your chainsaw only runs if the choke is on the problem, in most cases, is a result of fuel supply problems or a faulty carburetor. To fix the problem you should check and clean the fuel system and carburator.
Why does my Poulan chainsaw dies when I give it gas?
The carburetor might be clogged. A clogged carburetor is often caused by leaving fuel in the chainsaw for a long period of time. Over time, some of the ingredients in the fuel may evaporate, leaving behind a thicker, stickier substance. This sticky fuel can clog up the carburetor and cause the chainsaw engine to stall.
What is the LA screw on a Stihl chainsaw?
The LA setting on Stihl chainsaws is controlled by a screw on the outer housing of the engine that adjusts the flow of fuel and air through the carburetor. This screw is inside the engine housing on the carburetor, but is accessible through a hole or gap in the outer housing of the saw.
How do you fix a chainsaw that won’t stay running?
Clogged Air Filter – Check the air filter Your chainsaw’s engine needs the right supply of air to run properly. A clogged air filter can be the reason why your chainsaw won’t start or stay running. Find your chainsaw’s air filter and remove it. If it’s clogged or too dirty, wash it or replace it.
What does a spark arrestor do on a chainsaw?
The spark arrestor on your chainsaw prevents dangerous hot sparks from igniting fires while you’re working. If the arrestor is clogged or dirty, however, it will also prevent exhaust from leaving the motor, which can prevent it from running.
Why is my chainsaw losing power?
1. Dull chain and or improper lubrication to the bar and chain, sharpen and or clean the bars oil holes. 2. Air filter and fuel filter for restrictions and contamination, clean or replace as needed.
How do you tell if a carburetor is running rich or lean?
Q: How Do You Tell if a Carburetor Is Rich or Lean? A: One way to tell for sure is by “reading” the spark plugs. If the plug tip is white, the mixture is lean. If it’s brown or black, it’s rich.
What is running rich or lean?
A vehicle’s fuel mixture refers to the ratio of fuel and air in the combustion process. When you have too much fuel and not enough air, your car is considered to be running “rich”. When you have too much air and not enough fuel, your vehicle is considered to be running “lean”.
Is it better to run rich or lean?
TLDR – running just a little lean could improve fuel economy and give extra power. However, run too lean and you risk engine failure because the engine runs too hot. Whereas running rich can waste fuel and increase pollution but will not damage the engine.
What will happen if the carburetor is not properly adjusted?
Depending on the make and model of the vehicle, different carburetors may have multiple, sometimes up to four, air fuel mixture adjustment screws. These screws are responsible for controlling the amount of fuel that enters the engine, and improper adjustment will result in decreased engine performance.