The need to flip your chainsaw bar is better demonstrated when you consider the fact that the majority of the chainsaw’s cutting action takes place at the base of the bar. In all, how often your flip your chainsaw bar is dependent on your schedule and importantly, your chainsaw use. In conclusion, flipping your chainsaw bar could make all the difference in the longevity of your chainsaw bar as well as that of the chainsaw itself.
If you’ve spent any amount of time watching loggers work, you’ve undoubtedly seen a chainsaw equipped with an upside down chainsaw bar. Though your chainsaw applies oil to the bar to reduce the friction between the bar and the chain, over time, the areas of the bar that experience the most pressure will wear out faster as you might expect. Every chainsaw bar has been designed to be mounted right-side up or upside down.
When pruning we tend to use the end of the bar as we stretch to reach the limbs of the tree and then the third area is on top of the bar when there is the chance of the wood pinching the bar as the branch of the trunk begins to fall. The idea behind flipping the bar is to spread the wearing areas of the bar so that the bar not only lasts twice as long, but it also ensures a safer operation of the saw. Although flipping the bar will almost double the life of the bar there will come a time when the chain begins to wonder, and the safety of the saw is reduced.
If you’ve ever passed through logging country, you might have seen loggers using a chainsaw with all of the logos and words on the chainsaw bar upside down. Chainsaw bar rails – Chainsaw bar rails are a slot or groove around the perimeter of the chainsaw bar where the saw chain itself rides while the saw is in operation. Since a chainsaw accident is potentially deadly, chainsaw operators must scrutinize their chainsaw before every operation to ensure that no part of the chainsaw is worn or damaged and in need of attention.
when to flip chainsaw bar Related Question:
When should I reverse my chainsaw bar?
Every chainsaw bar has been designed to be mounted right-side up or upside down. The reason for this is that it allows the user to extend the life of his chainsaw bar by 50%. Flipping the bar will give the heavily-used areas some relief from wear and tear.
How often should I change the bar on my chainsaw?
If you are looking for a general idea for how often you should replace a chainsaw bar, a rule of thumb is to replace the bar of your chainsaw once after you have gone through three chains on the same bar.
What is the hole in the end of a chainsaw bar for?
These two holes are used to hold the saw blade. if your chainsaw blade not have holes or just have one hole. it not work. if you know how to drill, you can drill two holes on your chainsaw blade.
Why does my chainsaw blade dull so quickly?
Is the wood that you’re cutting with the chainsaw particularly dirty? Many chainsaw enthusiasts have noted that their blades dull faster when they’re cutting muddy wood. If the logs that you’re cutting up are muddy, then perhaps that is the sole reason why your blade is dulling too fast.
What chainsaw chains do professional loggers use?
Full-chisel teeth chains are usually used by professionals on large saws. Semi-chisel teeth are rounded, so the risk of kickback is less, and they stay sharper longer. Semi-chisel teeth cut slower but are a better choice in dirty wood than full chisel.
How long does a chainsaw chain stay sharp?
A chainsaw may only need to be sharpened once a year if it is rarely used, but a tool that is frequently used will need to be sharpened regularly to ensure that the blade doesn’t get too dull. On average, a chainsaw blade will retain its sharpness for about 3 hours of actively cutting through wood.
What size bar do loggers use?
A 20″ bar is about standard in the woods here, not many trees you can’t cut with a 20″ and a bit of work. I have 20″ on my 70cc saws, 24″ on my 385xp. I do have a 395 with a 32″ I mill with.
Why is my chainsaw bar smoking?
This most commonly is a result of a dull chain and exerting to much pressure on the bar and chain trying to make the chain saw cut. This could also be either a lack of bar and chain oil ( tank empty, restricted oiler hole ) or an inferior type of oil that is being slung off the chain and not lubricating.
Can you drill holes in chainsaw bar?
Re: Drilling a Chainsaw Bar Drilling that bar may not be as difficult as you think. It will be best if you use a drill press, start with a pilot hole, and then drill to the size you need. Make sure you have a sharp bit, run at the lowest speed you can, and use cutting fluid.
How long should a chainsaw last?
That being said, you can expect a quality chainsaw to last you at least 10 years or more. But if you take care of it, I know people who have saws that have lasted 20-30 years and even longer.
Is it OK to run a chainsaw without the bar?
I do not recommend letting it run for more than 5 minutes. Without a chain, the chainsaw will cause the engine to rev higher. This can eventually overheat the engine’s components and increase wear and tear.
Is it OK to cut wet wood with a chainsaw?
Can you cut wet wood with a chainsaw? Yes, you can cut the wet wood with a chainsaw. Besides, there is a misconception that wet wood can impact the chainsaw bar and chain. But actually, the damp wood will not dull the chainsaw any faster than using it on other types of wood.
How tight is too tight for chainsaw chain?
A properly-tensioned chainsaw chain should still be just a little loose on the chainsaw guide bar, but the chain needs to be tight enough that you can’t pull the drive links out of the bar nose.
Why is my chainsaw burning the wood?
Your chainsaw burns wood because of poor lubrication Lubrication allows the mechanical parts to coordinate much better by avoiding a phenomenon of friction which risks causing traces of burns. This is one of the main reasons that your appliance gives off too much heat and that the wood burns.
Why does a chainsaw cut crooked?
One major reason a chainsaw curves to either the right or left during a cut is that it was unevenly sharpened. The unequal teeth of the chain cause it to take a different-sized bite into the wood. What is this? The uneven sharpness of the chain is mainly due to manual sharpening, especially with the use of a file.