The one for the 026 doesnt look bad but when my 026s get dark like that I replace them. That one may be dark from improper cleaning so its hard to be for certain. Alot of the newer filters get dirty to the point they cant be cleaned and replacement is the only choice so as a precaution Id replace the 026 filter as well.
when to replace stihl chainsaw air filter Related Question:
When should I change my chainsaw air filter?
You should replace the filter once per year if the chainsaw has had plenty of use. It will depend on the rate of use and the amount of dirt and debris the unit has had to contend with. The air filter will gradually degrade and wear out.
Can you wash the air filter on a Stihl chainsaw?
What’s more, HD2 air filters can be easily cleaned and reused multiple times: just spray the removed filter with STIHL Varioclean, leave the detergent to take effect briefly, then rinse and dry the air filter before reinstalling it.
How do you clean a Stihl air filter?
Pull out the air filter with your fingers. Avoid prying it with a tool, which can damage it. Clean the air filter with compressed air or warm, soapy water. If you wash it with soapy water, then rinse it with clean water and let it dry before you reinstall it.
Why does my Stihl chainsaw keep cutting out?
The carburetor might be clogged. A clogged carburetor is often caused by leaving fuel in the chainsaw for a long period of time. Over time, some of the ingredients in the fuel may evaporate, leaving behind a thicker, stickier substance. This sticky fuel can clog up the carburetor and cause the chainsaw engine to stall.
How do I clean the oil tank on my Stihl chainsaw?
Half fill the tank, close, slosh around, leave sit a while, slosh some more and empty – repeat a few times. Then retrieve the filter line with a hooked wire, change filter, fill with white spirits again and run the saw a while to flush the chanells and pump.
How do you clean a Stihl HD2 air filter?
STIHL Varioclean is a multipurpose cleaner that cleans the HD2 filter with ease due to its specific pH value. Just spray it on, let it soak for 10 minutes and rinse it off. Let the filter air dry, reinstall it and you are ready to work.
Can I use 2 stroke oil on my air filter?
Can You Oil Air Filter With 2 Stroke Oil? nope. You can use mineral spirits, rinse well with water, and then use a little bell ray oil FILTER oil (sticky stuff), just like you would use on a dirt bike filter for your 2nd gen r6.
What can I use if I don’t have air filter oil?
Bar and chain oil is a fantastic substitute for air filter oil (which is basically a thick sticky oil with dye in it).
Can you use bar and chain oil on an air filter?
Chevy74. I’ve used chainsaw chain and bar oil countless times. Cheap, only $10 for a gallon and works great and is just as tacky as filter oil. I have had no ill effects whatsoever.
What is in an air filter?
An air filter is usually made of a spun fiberglass material or from pleated paper or cloth enclosed in a cardboard frame. It’s basic function is to clean the air that circulates through your heating and cooling system.
How often should I clean my chainsaw?
BEFORE AND AFTER EACH USE: Keep your chainsaw running smoothly by spending an extra minute or two before and after each use to inspect your chainsaw. Clean the chainsaw bar after each use by scraping out any debris inside the track.
Can I clean a chainsaw fuel filter?
Brush the air filter gently with a soft brush or wash it in warm soapy water then dry it. Do not use compressed air to clean it – compressed air can blow holes in the filter, allowing dust and debris into your carburetor.
Why does my chainsaw dies when I give it throttle?
If the filter becomes clogged, not enough fuel will reach the engine for it to run properly. Because your chainsaw will idle, but dies when it is revved up to full power, it means that the filter is only partially clogged; it will allow enough fuel to the engine to run on idle, but not enough to sustain full throttle.
Why does my chainsaw bog down at full throttle?
If your chainsaw is bogging down when you give it throttle, this is often a sign of improper gas-to-oil ratio. If there is too much gasoline in relation to the amount of oil used, this is known as a “rich mixture” and can cause the chainsaw to run poorly.
Why does my Stihl chainsaw bog down when I give it gas?
The Job of the Carburetor One controls the fuel mixture when the engine is idling, one controls it when the engine is operating at low speed and one is for high-speed fuel control. When the saw bogs down during cutting, it’s usually the high-speed screw you need to adjust.